Page 21 of 23
Re: PCM Hammer Release 014
Posted: Thu Jan 21, 2021 4:10 pm
by antus
that looks like an issue with the pcm or the car. the pcm is not accepting the kernel upload. if its in a car, try doing the flash on the bench. if its on the bench then you'll probably need to force the hardware in to recovery mode either write parameters or do a full write (clone) sending in a full bin you read before the problem started happening.
Re: PCM Hammer Release 014
Posted: Thu Jan 21, 2021 4:53 pm
by Tazzi
"PCM is already unlocked". Well... it shouldn't be unlocked already so is it in recovery mode???
Re: PCM Hammer Release 014
Posted: Thu Jan 21, 2021 11:54 pm
by MgFoster
Must be something from the write with ls droid that makes it think its in recovery mode? I can try a clone, I just assumed that would get caught up on the same step.
Re: PCM Hammer Release 014
Posted: Fri Jan 22, 2021 1:23 am
by Gampy
MgFoster wrote:then my phone updated to android 11 and the app crashed...
I'll assume "the app" is LS Droid, and did it crash during a write ??
If it did and you have a spare PCM, switch to it and use PCM Hammer!
Then get a replacement for your spare ...
BTW, the device (LX) you are using is a 1x device, disabling 4x does nothing.
Re: PCM Hammer Release 014
Posted: Fri Jan 22, 2021 1:35 am
by MgFoster
Gampy wrote:MgFoster wrote:then my phone updated to android 11 and the app crashed...
I'll assume "the app" is LS Droid, and did it crash during a write ??
No it crashed consistently at the time where you go to select "write calibration". The write before my phone updated was perfect and the ecu runs the engine fine.
Re: PCM Hammer Release 014
Posted: Fri Jan 22, 2021 2:22 am
by Gampy
Your getting properties (VIN, Serial Number, etc...) ... that's good.
It's saying it's already unlocked ... That's bad.
In my experience that typically means REBOOT!
My recommended boot procedure ...
Turn Ignition Off.
Disconnect battery power to PCM. (completely disconnect PCM)
Unplug Tool from PC. (or disconnect wireless)
Unplug Tool from DLC. (OBDII) (PCM)
Reboot PC ... While letting PCM set for a minute or two ...
Hookup ...
PC powered up and ready.
PCM hooked to battery, Ignition OFF.
Wait 10s
Plug Tool into DLC. (OBDII) (PCM)
Plug Tool into PC. (or connect wireless)
Wait 10s. (unless installing drivers, allow them to finish)
Start Pcm Hammer.
Turn on Ignition.
Re: PCM Hammer Release 014
Posted: Fri Jan 22, 2021 5:05 am
by MgFoster
Well, I found an old phone and was able to write my needed changes using lsdroid again. Something isn't playing nice!
Re: PCM Hammer Release 014
Posted: Fri Jan 22, 2021 5:14 am
by Gampy
Please try reading that PCM with PCM Hammer now and post logs if not successful.
Re: PCM Hammer Release 014
Posted: Fri Jan 22, 2021 12:25 pm
by Tazzi
MgFoster wrote:Well, I found an old phone and was able to write my needed changes using lsdroid again. Something isn't playing nice!
20210121_135430.jpg
Does it show the Seed/Key in LSDroid?
Re: PCM Hammer Release 014
Posted: Mon Jan 25, 2021 1:19 am
by MgFoster
Hey guys, sorry for the delayed response.
I attached "Debug2" which is a pcm hammer log from attempting to read the PCM again.