Re: Vlad's rides thread
Posted: Fri Jun 22, 2018 7:15 pm
Cheers !
pcmhacking.net
Electronic Fuel Injection - Developement & Tuning
https://pcmhacking.net/forums/
Vlad's rides thread
Page 277 of 345
Re: Vlad's rides thread
Posted: Sat Jun 23, 2018 3:37 pm
im not sure if it would bolt straight on or not but think about a VS fan, they are two speed and actually narrower than the VN-VR ones.
Re: Vlad's rides thread
Posted: Sat Jun 23, 2018 3:42 pm
I actually had VS fan provisions deleted off this radiator design as they were somewhat in the way. I have a good VS fan but I prefer the VN-VR type. Good excuse to get a new fan to match the theme going on here 
Re: Vlad's rides thread
Posted: Sat Jun 23, 2018 3:52 pm
Not too many pod filter have this design. It's about time they started doing this, the bellmouthed base.
Had to modify the CAI box to work around the orientation of the radiator filler. This was designed like this to clear VR bonnets and also clears VN/VP even better in fact.
Also need to get a 90º fitting like I did on the VR to allow better CAI lid fitment.
So the pod I got turned out to fit awesome. Just need to get the 30º aluminium pipe cut by a band saw. I have measured and marked it out already.
Had to modify the CAI box to work around the orientation of the radiator filler. This was designed like this to clear VR bonnets and also clears VN/VP even better in fact.
Also need to get a 90º fitting like I did on the VR to allow better CAI lid fitment.
So the pod I got turned out to fit awesome. Just need to get the 30º aluminium pipe cut by a band saw. I have measured and marked it out already.
Re: Vlad's rides thread
Posted: Sat Jun 23, 2018 5:50 pm
What Is the part number of the pod please?
Re: Vlad's rides thread
Posted: Sat Jun 23, 2018 6:18 pm
It's already on page 272.
Or if you are too lazy.
https://www.knfilters.com/search/produc ... =RX-4730XD
Or if you are too lazy.
https://www.knfilters.com/search/produc ... =RX-4730XD
Re: Vlad's rides thread
Posted: Mon Jun 25, 2018 8:00 pm
Got the fitting sorted.
Got a local engineering place up the road to cut my pipe with a band saw so it was neat and straight, unlike my attempts using a a grinder lol.
Filter fits good as and also held up nicely so it does not bang about on things. Just need to get some suitable pinch welt to line the hole so the pipe doesn't rattle. The VW pinch welt I had new in a box was too thin to fit on that thick plastic. Need to make a trip to clark rubber and get a proper sized one.
The whole thing now fits and screws together great with nothing stressing on it like before.
Got a local engineering place up the road to cut my pipe with a band saw so it was neat and straight, unlike my attempts using a a grinder lol.
Filter fits good as and also held up nicely so it does not bang about on things. Just need to get some suitable pinch welt to line the hole so the pipe doesn't rattle. The VW pinch welt I had new in a box was too thin to fit on that thick plastic. Need to make a trip to clark rubber and get a proper sized one.
The whole thing now fits and screws together great with nothing stressing on it like before.
Re: Vlad's rides thread
Posted: Tue Jun 26, 2018 5:15 pm
HOLY FUCKING SHIT!!! FINALLY!!! 
https://www.ebay.com.au/itm/Vp-Boot-Bad ... SwZb5bMbL0
Only took me 3+ years of nearly daily searching. About fucking time!
https://www.ebay.com.au/itm/Vp-Boot-Bad ... SwZb5bMbL0
Only took me 3+ years of nearly daily searching. About fucking time!
Re: Vlad's rides thread
Posted: Thu Jun 28, 2018 6:23 pm
Have you got a part number for that, I’m looking for onevlad01 wrote:HOLY FUCKING SHIT!!! FINALLY!!!
https://www.ebay.com.au/itm/Vp-Boot-Bad ... SwZb5bMbL0
Only took me 3+ years of nearly daily searching. About fucking time!
Re: Vlad's rides thread
Posted: Thu Jun 28, 2018 7:10 pm
it's on page 272.