Page 4 of 6
Re: VXDiag VCX Nano
Posted: Thu Apr 01, 2021 3:46 pm
by jxx
Tazzi wrote:Pulled mine apart to verify, does not have anything coming off of pin9 for GM UART.
Bugger.
That's why I purchased, needed something quick to do jobs while I waited for a new tech2 to arrive after the one I had died and other scantools I had access to didn't do what I needed.
The VCMII was the same, could use it for tec2win and as a j2534 device but no GM aldl, darn false advertising saying it works and doesn't........
Re: VXDiag VCX Nano
Posted: Fri Apr 02, 2021 4:39 am
by Gampy
jxx wrote:darn false advertising saying it works and doesn't........
[rant]
A pet peeve of mine ... I really dislike Liars, Cheats and Thieves and that is exactly what they are!
Especially when it comes to making a buck!
It is what it is, say what it is!
A perfect example where Capitalism trumps Democracy, for a Democracy to survive everyone must do their part, if you see a wrong you _must_ voice your opinion of that wrong, make it heard! or you are part of that wrong!
Too many, see in silence for fear of condemnation!
[/rant]
Re: VXDiag VCX Nano
Posted: Fri Apr 02, 2021 9:09 am
by The1
yeh my vxdiag has nothing connected on pin9 from what i can see, it does connect to the board but i can't see any traces, it uses a ARM STM32F407 im guessing most cables are just using the cheapest CAN capable chip and saying that it can do everything
Looks like if that had used the STM32F413 they would have uart then.
Re: VXDiag VCX Nano
Posted: Fri Apr 02, 2021 1:51 pm
by vs ss
Gampy,I do t know if these are the photos you want but I have a couple of mine.
Re: VXDiag VCX Nano
Posted: Fri Apr 02, 2021 3:10 pm
by Gampy
Thank ya sir!
Re: VXDiag VCX Nano
Posted: Sun Apr 04, 2021 3:11 pm
by The1
my genuine one bought from vxdiag store is same as above.
Re: VXDiag VCX Nano
Posted: Sun Apr 04, 2021 4:06 pm
by In-Tech
Mine too, I bought it to work with Tazzi's e38 stuff and it works great with his and pcmhammer and whatever so far. Of course I had to install all their BS with it. But if we are going to complain about bloated software installs...PCM hammer is ~ 80mb install to write a damit 512k file
I ain't plainin, it's coo as shite
Re: VXDiag VCX Nano
Posted: Sun Apr 04, 2021 5:22 pm
by Gampy
In-Tech wrote:But if we are going to complain about bloated software installs...PCM hammer is ~ 80mb install to write a damit 512k file
I ain't plainin, it's coo as shite
What the flock you talking about ... PcmHammer et al. isn't even 5MB!
- PcmHammer15_SizeOnDisk.png (9.78 KiB) Viewed 3949 times
Re: VXDiag VCX Nano
Posted: Mon Apr 05, 2021 2:13 am
by In-Tech
Well heck, I don't know wth I was looking at. I thought I checked out how big it was after install and evidently I was looking at something else...Sorry, you are correct, less than 5mb.
Re: VXDiag VCX Nano
Posted: Mon Apr 05, 2021 4:13 am
by Gampy
Must of had your beer goggles on ...
