Bingus wrote:Here is the bin I pulled from the 07 P12b I have. It is indeed 2MB.
It also took a lot longer to read due to failures - wondering if the resistor trick would help. I'm surprised at how unstable the P12b read was compared to the P12 I have.
Sure is, tested and confirmed when we added support for the 2Mb chips in pcmhammer. My p12b arrived last week. A couple of us now have one in hand. 07 models, service number 12602010.
anyone else have this issue were trying to read an entire pcm its file is 0Kb?.
im using the obdx Pro GT with the usb lead i can connect to it fine read the details etc ok but when i try to read the entire pcm it saves the file as 0Kb. i have only had it read successfully once so not to sure if it something ive done or not as seems to very straight forward program.
[03:07:23:009] PCM Hammer 021
[03:07:23:013] Sunday, October 08 2023 @03:07:23:01
[03:07:23:189] Thanks for using PCM Hammer.
[03:07:23:747] Device Found: OBDX Pro GT
[03:07:23:823] Device Successfully Initialized and Ready
[03:08:22:444] Will save to C:\Users\mechf\OneDrive\Desktop\Ecu Stuff\Tune FIles\Pcm Hammer Reads\Ls1 - 512Kb\0411_Test_Bench_Pcm.bin
[03:08:25:295] Querying operating system of current PCM.
[03:08:25:332] OSID: 1273002
[03:08:25:428] Unlock succeeded.
[03:08:25:454] Attempting switch to VPW 4x
[03:08:25:491] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[03:08:27:417] Kernel upload 48% complete.
[03:08:28:220] Kernel upload 100% complete.
[03:08:28:447] Kernel Version: 01030501
[03:08:28:449] kernel uploaded to PCM succesfully. Requesting data...
[03:08:28:461] Flash chip: Intel 28F400B, 512kb
[03:08:28:464] Read complete.
[03:08:28:466] All read-request messages succeeded on the first try. You have an excellent connection to the PCM.
[03:08:28:469] We're not sure how much retrying is normal for a read operation on a 0kb PCM.
[03:08:28:471] Please help by sharing your results in the PCM Hammer thread at pcmhacking.net.
[03:08:28:474] Starting verification...
[03:08:28:479] Calculating CRCs from file.
[03:08:28:483] Initializing CRC algorithm on PCM, this will take a minute...
[03:08:28:534] Requesting CRCs from PCM.
[03:08:28:538] Range File CRC PCM CRC Verdict Purpose
[03:08:28:540] 060000-07FFFF not needed not needed n/a OperatingSystem
[03:08:28:545] 040000-05FFFF not needed not needed n/a OperatingSystem
[03:08:28:549] 020000-03FFFF not needed not needed n/a OperatingSystem
[03:08:28:554] 008000-01FFFF not needed not needed n/a Calibration
[03:08:28:559] 006000-007FFF not needed not needed n/a Parameter
[03:08:28:572] 004000-005FFF not needed not needed n/a Parameter
[03:08:28:585] 000000-003FFF not needed not needed n/a Boot
[03:08:28:594] The contents of the file match the contents of the PCM.
[03:08:28:627] Clearing trouble codes.
[03:08:29:760] Clearing trouble codes.
[03:08:30:847] Elapsed time 00:00:05.4119664
[03:08:30:872] Saving contents to C:\Users\mechf\OneDrive\Desktop\Ecu Stuff\Tune FIles\Pcm Hammer Reads\Ls1 - 512Kb\0411_Test_Bench_Pcm.bin
Can you please post or PM me a debug log ... Results logs are useless for diagnostics, they provide little information.
Not that it's going to change anything, but there is a New TEST Version you could use to read with: I would wait to write important things yet, but it's looking good so far!
-Enjoy
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
The OSID is not recognised. Probably in a future version of pcmhammer we'll get the size from the flash chip definition instead of the osid definition (which doesnt exist, hence 0 bytes). But at this stage, that's not how it works.
