Page 58 of 97
Re: PCM Hammer - new ls1 flash tool
Posted: Mon Dec 16, 2019 9:28 am
by Gampy
The OBDLink MX+ should do more than 128 bytes at a time shouldn't it??
[edit]
Oh wow, my Sparkfun shrunk to 128 byte packets. bah humbug!
I get why ...
Re: PCM Hammer - new ls1 flash tool
Posted: Mon Dec 16, 2019 12:51 pm
by NSFW
I've never tried with an MX. I thought it would work, but I have a note saying that it won't, so I dunno.
Re: PCM Hammer - new ls1 flash tool
Posted: Mon Dec 16, 2019 12:53 pm
by antus
@gampy, if your able to test different packet sizes with your hardware and send a pull request that sets it appropriately based on device ID string that'd be great

Re: PCM Hammer - new ls1 flash tool
Posted: Mon Dec 16, 2019 2:13 pm
by Gampy
Already added a else if() for the SparkFun, Still bounds testing, IIRC it could only handle 245 + 12 on the Receive, forget what send was.
@PeterTremonti has a MX+ and has offered to help test, funny thing is, the MX+ should be detected, it's match is STN2255, that is what his tool reports.
I've suggested he try the new version, send a log, go from there.
Re: PCM Hammer - new ls1 flash tool
Posted: Mon Dec 16, 2019 11:09 pm
by Gampy
Huston we have a problem!
(At least I do)
I assumed (Arrrggg) that Read (download) works as good as it used to, was really only fully testing writing (uploading).
After getting mind blown with the following comment in my post notes.
Holy gulp ... Send at 2048, kernel uploads in 4 packets WHAM!
On the SparkFun!
However, time wise it is less then 4 tenths of a second faster over the complete upload at 2048*4 then 1024*8 packets.
So, 1024 is good.
Then, went to test MaxReceiveSize on the Sparkfun, it would not finish ... Switched to the Allpro, tried, failed, rebuilt with pure repo code (non of my mods), still fail.
Then I failed, Asleep!
A bit of log from earlier this AM.
[02:15:17:336] Processing message
[02:15:17:336] Recieved block starting at 493568 / 0x78800. 47%
[02:15:17:345] Sending 'test device present' notification.
[02:15:17:345] TX: AT SH 8C FE F0
[02:15:17:357] Set header response: OK
[02:15:17:358] TX: 3F
[02:15:17:990] Reading from 494592 / 0x78C00, length 1024 / 0x400
[02:15:17:991] TX: AT SH 6D 10 F0
[02:15:17:995] Set header response: OK
[02:15:17:995] TX: 35010400078C00
[02:15:18:631] RX: 6C F0 10 7F 34
[02:15:18:632] Processing message
[02:15:18:632] Unable to process response: UnexpectedResponse
[02:15:19:512] Timeout during receive.
[02:15:19:512] No payload following read request.
A bit of log from a few minutes ago
[07:52:39:997] Processing message
[07:52:40:006] Recieved block starting at 370688 / 0x5A800. 35%
[07:52:40:015] Sending 'test device present' notification.
[07:52:40:024] TX: AT SH 8C FE F0
[07:52:40:036] Set header response: OK
[07:52:40:044] TX: 3F
[07:52:40:685] Reading from 371712 / 0x5AC00, length 1024 / 0x400
[07:52:40:693] TX: AT SH 6D 10 F0
[07:52:40:705] Set header response: OK
[07:52:40:713] TX: 3501040005AC00
[07:52:41:461] RX: 6D F0 10 36 01 00 00 05 AC 00 02 78 FE 7F AD 54 87 78 AD 54 08 38 00 06 AD 54 66 0A 08 38 00 02 AC 00 67 00 00 DE 4A B8 AC 0A 66 46 4A 78 AC 1A 66 00 00 B0 08 38 00 06 AD 54 67 20 36 38 AC 14 38 39 00 01 C7 E8 B8 43 65 02 26 04 31 C3 AC 0E 31 C3 AC 14 42 38 AC 1D 60 00 00 88 34 79 00 01 C7 C0 31 CA AC 10 31 CA AC 16 11 FC 00 01 AC 1D 60 70 4A 78 AC 1A 66 6A 08 38 00 06 AD 54 67 30 36 38 AC 14 31 C3 AC 0E 38 39 00 01 C7 E8 B6 44 64 02 26 04 31 C3 AC 0E D6 79 00 01 C7 C6 64 04 36 3C FF FF 31 C3 AC 0E 31 C3 AC 14 70 02 60 2E 36 39 00 01 C7 C0 D6 79 00 01 C7 C4 64 04 36 3C FF FF 31 C3 AC 10 36 39 00 01 C7 C0 D6 79 00 01 C7 C4 64 04 36 3C FF FF 31 C3 AC 16 70 03 11 C0 AC 1D 08 38 00 06 AD 54 67 0A 21 F9 00 01 C7 EA AC 0A 60 7A 42 83 36 39 00 01 C7 C2 21 C3 AC 0A 60 6C 24 78 B5 D4 42 85 3A 2A 00 0A 26 38 AC 0A 96 85 64 02 42 83 21 C3 AC 0A 08 38 00 06 95 E5 66 2C 16 38 95 DD 67 06 0C 03 00 03 66 04 76 01 60 02 42 03 4A 03 67 16 24 78 B5 D4 36 38 AC 0E 96 6A 00 0A 64 02 42 43 31 C3 AC 0E 60 20 08 38 00 06 95 E5 67 18 4A 78 AC 1A 66 12 4A 78 AC 0E 67 0C 31 F8 AC 14 AC 0E 11 FC 00 04 AC 1D 4A 78 AC 10 67 46 36 38 AD 54 EE 4B 02 03 00 03 0C 03 00 02 66 0E 4A 38 AC 1C 66 0C 11 FC 00 01 AC 1C 60 04 42 38 AC 1C 4A 38 AC 1C 67 16 24 78 B5 D4 36 38 AC 10 96 6A 00 0A 64 02 42 43 31 C3 AC 10 60 0C 31 F8 AC 16 AC 10 60 04 42 38 AC 1C 16 38 95 DD 0C 03 00 04 67 06 0C 03 00 02 66 04 76 01 60 02 42 03 4A 03 67 5A 16 38 AC 12 52 03 64 04 16 3C 00 FF 11 C3 AC 12 38 39 00 01 C7 E8 3A 38 AC 14 BA 44 65 02 28 05 31 C4 AC 18 B6 39 00 01 C7 CA 65 26 36 38 AC 18 96 79 00 01 C7 C8 64 02 42 43 31 C3 AC 18 38 39 00 01 C7 E8 B6 44 64 02 26 04 31 C3 AC 18 42 38 AC 12 31 F8 AC 18 AC 14 60 04 42 38 AC 12 08 38 00 07 AF 70 66 4E 4A 78 AC 1A 66 32 16 38 95 8E B6 39 00 01 C7 AA 64 16 34 79 00 01 C7 AC 31 CA AC 1A 31 CA AC 0E 11 FC 00 05 AC 1D 60 2A B6 39 00 01 C7 AB 63 22 31 F8 AC 0E AC 1A 60 1A 24 78 B5 D4 36 38 AC 1A 96 6A 00 0A 64 02 42 43 31 C3 AC 1A 60 04 42 78 AC 1A 36 38 AD 54 EE 4B 02 03 00 03 0C 03 00 02 66 1A 4A 78 AC 0E 66 0E 4A 78 AC 10 66 08 11 FC 00 06 AC 1D 60 06 02 78 FE 7F AD 54 4C DF 01 07 4E 5E 4E 75 48 E7 E0 80 16 38 95 8E B6 39 00 01 C7 FA 62 0E 08 F8 00 07 AC 01 08 B8 00 06 AC 01 60 14 B6 39 00 01 C7 FB 65 0C 08 B8 00 07 AC 01 08 F8 00 06 AC 01 16 38 95 DC 72 01 B2 03 62 24 0C 03 00 02 62 1E 08 38 00 07 AC 01 67 0C 11 C1 AC 1E 08 F8 00 05 AC 00 60 1A 08 38 00 06 AC 01 67 12 60 06 0C 03 00 03 66 0A 42 38 AC 1E 08 B8 00 05 AC 00 4A 03 67 4E 20 7C 00 FF AC 20 4E B9 00 05 CC 84 4A 00 67 3E 4A 38 B5 1B 66 38 08 38 00 05 AC 00 67 30 0C 38 00 02 95 DC 66 28 3A 39 00 01 C7 F6 48 C5 42 83 36 38 AC 20 D6 85 4A 83 6D 0E 0C 83 00 00 FF FF 63 08 36 3C FF FF 60 02 42 43 31 C3 AC 20 4C DF 01 07 4E 75 36 38 95 DA B6 78 AC 20 62 08 08 38 00 03 AC 00 67 08 08 F8 00 06 AC 00 60 06 08 B8 00 06 AC 00 4E 75 08 B8 00 05 AC 01 16 38 95 DC 67 68 0C 78 FF FF AC 20 67 60 4A 38 AC 1E 67 06 0C 03 00 01 67 54 08 38 00 03 AC 00 66 54 02 43 00 FF 38 38 95 DA B8 70 33 B0 00 01 C7 DA 63 3A B8 78 AC 20 63 34 16 38 95 F2 0C 03 00 02 67 0C 0C 03 00 01 67 06 0C 03 00 03 66 26 36 38 9B C2 B6 78 9B C0 62 1C 4A 39 00 01 C7 90 67 14 4A 38 9B C6 66 0E 08 F8 00 05 AC 01 08 B8 00 06 AC 00 60 06 08 F8 00 06 AC 00 4E 75 08 B8 00 05 AC 01 16 38 95 DC 67 5A 0C 78 FF FF AC 20 67 52 4A 38 AC 1E 67 06 0C 03 00 01 67 46 08 38 00 03 AC 00 66 46 36 38 95 DA B6 78 AC 20 63 34 16 38 95 F2 0C 03 00 02 67 0C 0C 03 00 01 67 06 0C 03 00 03 66 26 36 38 9B C2 B6 78 9B C0 62 1C 4A 39 00 01 C7 90 67 14 4A 38 9B C6 66 0E 08 F8 00 05 AC 01 08 B8 00 06 AC 00 60 06 08 F8 00 06 AC 00 4E 75 4A 38 AC 5D 67 08 08 38 00 05 AF 70 67 08 08 38 00 04 AF CA 67 08 11 FC 00 03 AD 5B 60 50 16 38 95 DC 0C 03 00 03 66 1E 4A 38 AC 5E 67 18 08 38 00 05 AD 59 66 10 08 38 00 04 AD 58 66 08 11 FC 00 01 AD 5B 60 28 4A 38 AC 60 67 1E 0C 03 00 02 65 18 08 38 00 07 AF 70 67 10 08 38 00 05 AD 59 66 08 08 38 00 04 AD 58 67 D4 42 38 AD 5B 4E 75 08 F8 00 06 AC 01 08 F8 00 05 AB FC 08 F8 00 04 AC 01 4E 75 2F 00 16 38 AD 54 E2 0B 78 03 C6 04 B8 03 66 0A 11 FC 00 06 AD 52 60 00 00 CC 7A 02 BA 03 66 2E 08 38 00 05 AD 54 67 1C 08 38 00 07 AB FC 67 0A 11 FC 00 05 AD 52 60 00 00 AC 11 FC 00 04 AD 52 60 00 00 A2 11 FC 00 07 AD 52 60 00 00 98 70 01 B0 03 66 18 08 38 00 04 AD 54 67 08 42 38 AD 52 60 00 00 82 11 FC 00 08 AD 52 60 78 16 38 AD 5B B8 03 67 E8 B0 03 66 18 08 38 00 05 AD 54 67 0A 08 38 00 07 AB FC 66 A8 60 B0 11 C5 AD 52 60 54 BA 03 66 0E 08 38 00 04 AD 54 66 C0 11 C0 AD 52 60 42 08 38 00 07 AD 54 66 B2 4A 38 95 DC 67 AC 36 38 AD 54 EE 4B C6 04 BA 03 67 BC B0 03 66 0E 08 38 00 04 AD 54 67 D4 11 C4 AD 52 60 16 08 38 00 05 AD 54 66 AA 08 38 00 04 AD 54 66 EA 11 FC 00 09 AD 52 20 1F 4E 75 11 F8
[07:52:41:497] Processing message
[07:52:41:508] Unable to process response: Truncated
[07:52:41:817] RX: E9 5D E4 24 31 63 89 5D DC 6F C0 00 A4 24 41 83 8A D5 2D 64 41 1F 03 5B 00 00 03 ED EA D5 03 1F 03 5B 00 00 03 ED CA D4 E0 8B 80 00 4A 40 04 A3 8A D5 06 70 60 8F 80 00 4A 40 01 1F 8A D4 F9 5D D4 E7 53 63 8B 44 84 20 4D 64 30 28 30 00 0F FF F8 6F C0 00 3F 83 93 14 00 00 1C 93 C3 1C 3A 41 84 24 31 63 89 5D D2 47 03 5B 00 00 8A 4E 24 ED 24 EB 90 00 5B 31 E6 03 00 8B 80 00 5A D5 40 8F 80 00 4A D5 44 EB 90 00 5B 34 46 01 C0 8B 80 00 4A D5 44 E7 14 EB 90 00 5B 2C 86 00 C0 8B 80 00 5A D5 44 EB 90 00 5C 19 64 EB 90 00 5C 5E 44 EB 90 00 5C 32 24 EB 90 00 5C 36 64 E7 54 EB 90 00 5B 59 A4 A3 90 00 19 6B 06 74 61 63 89 5D D0 C0 30 00 56 61 44 EB 90 00 5B 6C A4 EB 90 00 5B 88 44 EB 90 00 5C 05 46 02 80 C0 30 00 46 70 60 C0 30 00 26 60 47 60 16 00 24 20 34 A0 36 71 24 EB 90 00 5B 6C A4 EB 90 00 5B 88 44 EB 90 00 5B C1 E4 E7 51 63 8A 2B C6 71 E0 C0 30 08 06 20 C0 24 30 0F FE F4 33 1C 3A 40 A6 00 63 1F C4 00 0A 40 A1 1F C0 00 1A 40 E4 E7 54 23 8A 40 E0 8B 80 00 5A 40 24 A3 8A C5 F6 70 64 27 8A 40 A6 02 63 63 89 5D AB 67 90 00 1C 77 66 30 A3 1F 90 00 1C 89 0A 40 A6 01 0B 67 90 00 1C 77 46 20 83 1F 90 00 1C 86 6A 40 A2 47 8B 5D 43 63 8A 40 4D 66 A0 00 A6 40 43 63 CF FF F3 1C 3A 40 44 E7 54 8E 7C 00 04 EB 90 00 5A 39 23 1C 0A D4 C3 63 89 5B C6 C0 44 44 36 90 89 67 8A D4 C6 80 C6 A0 63 63 C7 FF F6 00 43 63 C8 00 03 1C 3A D4 A3 63 89 5C 8C 6F 90 00 1C 86 88 6F C0 08 06 90 A4 A4 36 D0 60 C4 31 80 06 F0 43 63 C1 80 03 A3 89 5A C3 03 C0 C8 0B 04 56 30 44 24 56 01 60 C4 56 40 06 40 C9 A4 04 8C 5E B8 58 BF C0 0A F6 00 43 A3 C1 00 0F 83 95 94 00 00 1C 86 AD 64 50
[07:52:41:838] Processing message
[07:52:41:851] Unable to process response: UnexpectedResponse
[07:52:42:739] Timeout during receive.
[07:52:42:747] No payload following read request.
[07:52:43:636] Timeout during receive.
[07:52:43:644] No payload following read request.
[07:52:44:532] Timeout during receive.
[07:52:44:541] No payload following read request.
[07:52:45:429] Timeout during receive.
[07:52:45:437] No payload following read request.
[07:52:46:325] Timeout during receive.
[07:52:46:333] No payload following read request.
[07:52:47:222] Timeout during receive.
[07:52:47:230] No payload following read request.
[07:52:48:118] Timeout during receive.
[07:52:48:126] No payload following read request
Have rebooted a half dozen times, including the PC.
Re: PCM Hammer - new ls1 flash tool
Posted: Tue Dec 17, 2019 12:01 am
by PeterTremonti
I had inlaws in town for the weekend and left my scanner in the car I'm letting yhem borrow. I'll try and test the MX+ tomorrow sometime.
Re: PCM Hammer - new ls1 flash tool
Posted: Tue Dec 17, 2019 7:35 am
by NSFW
Gampy, I suspect that's due to either the timeout being too short or the MaxReceiveSize being too large. Only way to find out is to test with different values of each.
Re: PCM Hammer - new ls1 flash tool
Posted: Tue Dec 17, 2019 9:09 pm
by Tazzi
Kernel is running super smooth! Calibration write in 41seconds!
Code: Select all
[07:07:14:986] PCM Hammer (17/12/2019, 6:32 PM)
[07:07:15:326] Device Found: OBDX Pro VT
[07:07:15:335] Device Successfully Initialized and Ready
[07:07:21:273] C:\Users\Jason\Desktop\abc - edited.bin
[07:07:22:372] Validating 1024k file.
[07:07:22:378] Start End Stored Needed Verdict Segment Name
[07:07:22:382] 00000 FFFFD 7293 7293 Good Operating system
[07:07:22:384] 08002 162DF 312E 312E Good Engine calibration
[07:07:22:389] 162E2 1964F 7EB3 7EB3 Good Engine diagnostics.
[07:07:22:392] 19652 1D8DF 72D6 72D6 Good Transmission calibration
[07:07:22:395] 1D8E2 1E1DF FBC3 FBC3 Good Transmission diagnostics
[07:07:22:410] 1E1E2 1F6EF 5E21 5E21 Good Fuel system
[07:07:22:413] 1F6F2 1FEDF 5BC0 5BC0 Good System
[07:07:22:424] 1FEE2 1FFCF C25B C25B Good Speedometer
[07:07:22:441] Requesting operating system ID...
[07:07:22:474] PCM and file are both operating system 12592433
[07:07:22:532] Unlock succeeded.
[07:07:22:542] Attempting switch to VPW 4x
[07:07:22:570] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[07:07:23:597] Uploading kernel to PCM.
[07:07:24:004] Kernel upload 24% complete.
[07:07:24:403] Kernel upload 49% complete.
[07:07:24:803] Kernel upload 74% complete.
[07:07:25:202] Kernel upload 100% complete.
[07:07:25:539] Kernel Version: 010300BB
[07:07:25:545] Kernel uploaded to PCM succesfully.
[07:07:28:070] PCM and image file are both operating system 12592433
[07:07:28:105] Flash chip: AMD AM29F800BB, 1mb
[07:07:28:112] Calculating CRCs from file...
[07:07:28:121] Requesting CRCs from PCM...
[07:07:28:179] Range File CRC PCM CRC Verdict Purpose
[07:07:28:185] 0F0000-0FFFFF not needed not needed n/a OperatingSystem
[07:07:28:191] 0E0000-0EFFFF not needed not needed n/a OperatingSystem
[07:07:28:210] 0D0000-0DFFFF not needed not needed n/a OperatingSystem
[07:07:28:225] 0C0000-0CFFFF not needed not needed n/a OperatingSystem
[07:07:28:243] 0B0000-0BFFFF not needed not needed n/a OperatingSystem
[07:07:28:259] 0A0000-0AFFFF not needed not needed n/a OperatingSystem
[07:07:28:280] 090000-09FFFF not needed not needed n/a OperatingSystem
[07:07:28:295] 080000-08FFFF not needed not needed n/a OperatingSystem
[07:07:28:313] 070000-07FFFF not needed not needed n/a OperatingSystem
[07:07:28:322] 060000-06FFFF not needed not needed n/a OperatingSystem
[07:07:28:331] 050000-05FFFF not needed not needed n/a OperatingSystem
[07:07:28:359] 040000-04FFFF not needed not needed n/a OperatingSystem
[07:07:28:369] 030000-03FFFF not needed not needed n/a OperatingSystem
[07:07:28:379] 020000-02FFFF not needed not needed n/a OperatingSystem
[07:07:29:939] 010000-01FFFF A72B22AC 22793D52 Different Calibration
[07:07:31:521] 008000-00FFFF D9B00A53 D9B00A53 Same Calibration
[07:07:31:531] 006000-007FFF not needed not needed n/a Parameter
[07:07:31:540] 004000-005FFF not needed not needed n/a Parameter
[07:07:31:551] 000000-003FFF not needed not needed n/a Boot
[07:07:31:561] Processing range 010000-01FFFF
[07:07:31:570] Erasing.
[07:07:31:993] Writing...
[07:07:32:001] Sending payload with offset 0x0000, start address 0x010000, length 0x0800.
[07:07:32:924] Sending payload with offset 0x0800, start address 0x010800, length 0x0800.
[07:07:33:836] Sending payload with offset 0x1000, start address 0x011000, length 0x0800.
[07:07:34:750] Sending payload with offset 0x1800, start address 0x011800, length 0x0800.
[07:07:35:681] Sending payload with offset 0x2000, start address 0x012000, length 0x0800.
[07:07:36:619] Sending payload with offset 0x2800, start address 0x012800, length 0x0800.
[07:07:37:544] Sending payload with offset 0x3000, start address 0x013000, length 0x0800.
[07:07:38:457] Sending payload with offset 0x3800, start address 0x013800, length 0x0800.
[07:07:39:377] Sending payload with offset 0x4000, start address 0x014000, length 0x0800.
[07:07:40:295] Sending payload with offset 0x4800, start address 0x014800, length 0x0800.
[07:07:41:228] Sending payload with offset 0x5000, start address 0x015000, length 0x0800.
[07:07:42:156] Sending payload with offset 0x5800, start address 0x015800, length 0x0800.
[07:07:43:082] Sending payload with offset 0x6000, start address 0x016000, length 0x0800.
[07:07:44:029] Sending payload with offset 0x6800, start address 0x016800, length 0x0800.
[07:07:44:953] Sending payload with offset 0x7000, start address 0x017000, length 0x0800.
[07:07:45:398] Sending payload with offset 0x7800, start address 0x017800, length 0x0800.
[07:07:46:313] Sending payload with offset 0x8000, start address 0x018000, length 0x0800.
[07:07:47:219] Sending payload with offset 0x8800, start address 0x018800, length 0x0800.
[07:07:47:670] Sending payload with offset 0x9000, start address 0x019000, length 0x0800.
[07:07:48:119] Sending payload with offset 0x9800, start address 0x019800, length 0x0800.
[07:07:48:570] Sending payload with offset 0xA000, start address 0x01A000, length 0x0800.
[07:07:49:507] Sending payload with offset 0xA800, start address 0x01A800, length 0x0800.
[07:07:50:440] Sending payload with offset 0xB000, start address 0x01B000, length 0x0800.
[07:07:51:361] Sending payload with offset 0xB800, start address 0x01B800, length 0x0800.
[07:07:52:289] Sending payload with offset 0xC000, start address 0x01C000, length 0x0800.
[07:07:53:222] Sending payload with offset 0xC800, start address 0x01C800, length 0x0800.
[07:07:54:164] Sending payload with offset 0xD000, start address 0x01D000, length 0x0800.
[07:07:55:087] Sending payload with offset 0xD800, start address 0x01D800, length 0x0800.
[07:07:56:023] Sending payload with offset 0xE000, start address 0x01E000, length 0x0800.
[07:07:56:958] Sending payload with offset 0xE800, start address 0x01E800, length 0x0800.
[07:07:57:876] Sending payload with offset 0xF000, start address 0x01F000, length 0x0800.
[07:07:58:772] Sending payload with offset 0xF800, start address 0x01F800, length 0x0800.
[07:07:59:713] Retry count for this block: 28
[07:07:59:717] Calculating CRCs from file...
[07:07:59:724] Requesting CRCs from PCM...
[07:07:59:787] Range File CRC PCM CRC Verdict Purpose
[07:07:59:791] 0F0000-0FFFFF not needed not needed n/a OperatingSystem
[07:07:59:794] 0E0000-0EFFFF not needed not needed n/a OperatingSystem
[07:07:59:800] 0D0000-0DFFFF not needed not needed n/a OperatingSystem
[07:07:59:804] 0C0000-0CFFFF not needed not needed n/a OperatingSystem
[07:07:59:814] 0B0000-0BFFFF not needed not needed n/a OperatingSystem
[07:07:59:819] 0A0000-0AFFFF not needed not needed n/a OperatingSystem
[07:07:59:824] 090000-09FFFF not needed not needed n/a OperatingSystem
[07:07:59:829] 080000-08FFFF not needed not needed n/a OperatingSystem
[07:07:59:844] 070000-07FFFF not needed not needed n/a OperatingSystem
[07:07:59:854] 060000-06FFFF not needed not needed n/a OperatingSystem
[07:07:59:861] 050000-05FFFF not needed not needed n/a OperatingSystem
[07:07:59:876] 040000-04FFFF not needed not needed n/a OperatingSystem
[07:07:59:892] 030000-03FFFF not needed not needed n/a OperatingSystem
[07:07:59:910] 020000-02FFFF not needed not needed n/a OperatingSystem
[07:08:01:482] 010000-01FFFF A72B22AC A72B22AC Same Calibration
[07:08:03:061] 008000-00FFFF D9B00A53 D9B00A53 Same Calibration
[07:08:03:069] 006000-007FFF not needed not needed n/a Parameter
[07:08:03:078] 004000-005FFF not needed not needed n/a Parameter
[07:08:03:086] 000000-003FFF not needed not needed n/a Boot
[07:08:03:095] All ranges are identical.
[07:08:03:112] Clearing trouble codes.
[07:08:03:639] Elapsed time 00:00:41.1016298
Re: PCM Hammer - new ls1 flash tool
Posted: Wed Dec 18, 2019 3:27 am
by DavidBraley
I see in the PCM Hammer log above that the recognized device is a OBDX Pro VT. Where can someone get one of these? Or is this the device that Pete is developing with another guy? I think this is the site they are putting together now for future release:
https://obdxpro.com/
Re: PCM Hammer - new ls1 flash tool
Posted: Wed Dec 18, 2019 7:58 am
by NSFW
DavidBraley wrote:I see in the PCM Hammer log above that the recognized device is a OBDX Pro VT. Where can someone get one of these? Or is this the device that Pete is developing with another guy? [/url]
Yes it's that device, and "another guy" is who posted that log.
