Page 7 of 11
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 4:47 pm
by vx_commodore
Dylan wrote:In the enhanced section in custom code forum.
If you've modified the enhanced bin with another xdf loqded and saved it that could cause problems.
Yes write the bin I posted straight up. Maybe download it again to be sure it's unmolested. Untill good fuel.
OK. I'll look for that enhansed XDF. Download it. Then redownload you're until good fuel bin. And I'll try load that on in a few minutes.
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 4:50 pm
by Dylan
VATS off is the default so don't even need to open it. Download again and write it.
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 5:00 pm
by vx_commodore
Dylan wrote:VATS off is the default so don't even need to open it. Download again and write it.
Ok, I dident redownload any XDF as there is no XDF listed for the VX v6 N/A.
I did delete all old copies of untillgoodfuel .Bin, And re-downloaded that.
Did a Write Cal with the new untouched untillgoodfuel. Write success. But still wont start...
Turns over, Starts for a split second then dies.
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 5:03 pm
by Dylan
Can you do a write bin? The enhanced bins are modified code so may not be compatible.
Download the VXV6 file. It's a zipped folder with a bin xdf and adx. All matching.
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 5:07 pm
by vx_commodore
Dylan wrote:Can you do a write bin? The enhanced bins are modified code so may not be compatible.
Download the VXV6 file. It's a zipped folder with a bin xdf and adx. All matching.
Is it safe to do a Write bin?
It sais 'only do this if upgrading, Do write cal for any changes.'
Could you send a link to the location of that zipped Vx v6 folder? Cant seem to find it.
So, do a Write BIN with untillgoodfuel? Instead of doing a WRITE CAL?
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 5:15 pm
by Dylan
Im on my phone but go to the enhanced thread and just click on vx v6 na or however it's worded.
Then windows does it's download prompts.
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 5:19 pm
by vx_commodore
Dylan wrote:Im on my phone but go to the enhanced thread and just click on vx v6 na or however it's worded.
Then windows does it's download prompts.
Had another look, Cant seem to find VX v6 NA. They have VT,VX supercharged and VY, But no VX NA.
- Capture3.JPG (75.21 KiB) Viewed 4133 times
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 5:26 pm
by Dylan
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 5:31 pm
by vx_commodore
Oh, Sorry i must have looking in the wrong place.
Ok all downloaded.
So apply the new XDF, And retry the BIN to PCM?
Re: Can anyone help out a newby with ECU logging/hacking?
Posted: Fri Aug 07, 2015 5:33 pm
by Dylan
Are you writing to the ecu with ose flash tool?
If so just open the .bin and write. No xdf needed. That's for TunerPro.