Page 249 of 339
Re: Vlad's rides thread
Posted: Tue Jul 04, 2017 11:59 am
by FXST02
vlad01 wrote:Anyone have dimensions for ls2 coils? PN D514A.
Looked high and low and internet has 1 China copy result which is so low res it's unreadable.
All I could find was this:
https://www.amazon.com/ACDelco-D514A-Or ... B000IZ2C3K
Product Dimensions 4.3 x 2.7 x 2.7 inches
Which in English is 109.22mm x 68.58mm x 68.58mm, I'm pretty sure these sizes of the boxes that a coil comes in, but it's a starting point.
Re: Vlad's rides thread
Posted: Tue Jul 04, 2017 12:21 pm
by delcowizzid
I could dig an ls2 truck coil with heatsink out and measure if you need
Re: Vlad's rides thread
Posted: Tue Jul 04, 2017 12:52 pm
by Holden202T
I have LS2 coils at home ?
Re: Vlad's rides thread
Posted: Tue Jul 04, 2017 2:31 pm
by vlad01
Yeah see if they are the same as what I need measurements for. The Gm PN ends with 290. Ls2 truck ones are a fatter than that ones I'm planing to use.
Re: Vlad's rides thread
Posted: Tue Jul 04, 2017 3:03 pm
by Gareth
Why do you need the specs? what are you up to?
Re: Vlad's rides thread
Posted: Tue Jul 04, 2017 3:39 pm
by vlad01
So I can see if they will fit in place of the dfi and coil pack without interfering with anything and the bonnet.
Re: Vlad's rides thread
Posted: Wed Jul 05, 2017 10:17 pm
by vlad01
Anyone got a 3d printer and willing to print me a high res prototype once I have the file ready?
Its for those c pillar trims, getting them scanned real soon and modeled for CNC reproduction but ideally I would like to print one out for a test fit.
Re: Vlad's rides thread
Posted: Fri Jul 07, 2017 9:59 am
by Holden202T
- 20170706_185213_1499331422713_resized.jpg (229.84 KiB) Viewed 5110 times
- 20170706_185222_1499331425071_resized.jpg (160.18 KiB) Viewed 5110 times
Re: Vlad's rides thread
Posted: Sat Jul 08, 2017 12:21 am
by vlad01
Not the exact one I plan to use but the dimensions should be very similar from photos comparing them looking about the same, these are a bit longer and taller but seem to be slightly more narrow.
In other news I got all my connectors but I forgot to order the oil pressure switch one lol. Oh well good excuse to get the LS2 coil connectors and maybe a delphi 24 way micro-pack and I might look for a OBD 2 connector I can attached under the dash passenger size.
Also I sent off the c pillar trim for scanning.
Re: Vlad's rides thread
Posted: Sat Jul 08, 2017 10:26 pm
by vlad01
I got these done tonight, Turned out alright.
I had to modify a spare set of dies to do the injector ones because they aren't designed to do sealed terminals. Worked well but a few other connectors I have will require a end mill to machine out those strain relief die areas so I can get to the actual wire crimping without destroying the whole terminal as I already tested with a few spares.
So I will try to get the die to the engineer and do a quick mod for me. The steel is shit hard, took me over 10 min of solid grinding with a carbide burr to take away about 1mm.