OSE 11P V104
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: OSE 11P V104
and likewise the spreadsheet doesn't support every tune type on here, but they can be added to a new tab in the spreadsheet.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
-
- Posts: 1837
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: OSE 11P V104
I have a question with 11P. When I search for the word knock I am given four code 43- Knock sensor failure boxes to tick. Do need to tick all of them?
- vlad01
- Posts: 7810
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: OSE 11P V104
I have noticed this too, every item seems to have 4 of the same flag. I found I had to check them all otherwise TP would complain the same item had both states at the same time or something along those lines.
Don't have that issue in any other code base or XDF, only in 11P
Don't have that issue in any other code base or XDF, only in 11P
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: OSE 11P V104
Do you have the layout set right? Can't remember the name but little folders with the name like fuel or spark then all the flags tables scalers for that group. There's engine and trans section fault codes, then process code and CEL flags to for the fault code.
Post a screen shot and I'll know more. Only used 11P a few times but have masked a lot of codes and found it easy enough to navigate when laid out like that.
Post a screen shot and I'll know more. Only used 11P a few times but have masked a lot of codes and found it easy enough to navigate when laid out like that.
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: OSE 11P V104
There are 4 flags, its meant to be that way. There are essentially two operating systems in 11P, one for engine and one trans so there ends up being two lots of flags.
The process flag actually checks for the fault and then reacts to it. The CEL flag is so if you want to be notified via the CEL.
The process flag actually checks for the fault and then reacts to it. The CEL flag is so if you want to be notified via the CEL.
-
- Posts: 1837
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: OSE 11P V104
Thanks. I now understand.
Re: OSE 11P V104
Hi all..
I am wondering if anyone can please help me regarding the engine map switching within the 11P code?
Does the map switch while engine is running? And how quickly will it switch?
I am looking at running nitrous on my engine and would like to use this feature to pull timing at the same time as when the No2 "button" is pressed enabling the fogger.
Is this possible with the 11P code map switch feature?
Thanks
BARBS
I am wondering if anyone can please help me regarding the engine map switching within the 11P code?
Does the map switch while engine is running? And how quickly will it switch?
I am looking at running nitrous on my engine and would like to use this feature to pull timing at the same time as when the No2 "button" is pressed enabling the fogger.
Is this possible with the 11P code map switch feature?
Thanks
BARBS
-
- Posts: 1837
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: OSE 11P V104
On the fly. I just push the power/economy button while driving. My assumption is it changes straight away.
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: OSE 11P V104
Pwr/Econ input is polled by the code every 25ms, differrent parts of the code use it at various intervals. You can also use the flex output to trigger the nitrous system and which can in turn switch the pwr/econ input, the flex output is controlled every 100ms.
So yeah pretty much instantly and on the fly.
So yeah pretty much instantly and on the fly.
Re: OSE 11P V104
Hi all,
Has anyone here had issues with $11p and trying to lock a trans in 3rd gear? I have been trying to lock a trans in 3rd on the dyno and when I use the commands to lock both solenoids off it won't work.
Any advice on this would be great. $11p tune, ADX and XDF
Has anyone here had issues with $11p and trying to lock a trans in 3rd gear? I have been trying to lock a trans in 3rd on the dyno and when I use the commands to lock both solenoids off it won't work.
Any advice on this would be great. $11p tune, ADX and XDF