How to convert a 202 to Delco

Converting To Delco ECU From Carby Or Other Injection Systems
User avatar
Posts: 9495
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: How to convert a 202 to Delco

Postby Holden202T » Thu Jan 04, 2018 7:55 am

1. yes

2. yes they can, take note of them before you cut the plugs off, the larger lug is the positive wire.

Posts: 3
Joined: Sun Oct 14, 2018 5:27 pm
Location: Gin Gin Qld

Re: How to convert a 202 to Delco

Postby HoldenHj2001 » Tue Oct 16, 2018 7:02 pm

Hey guys I know this is an older thread but I’m in need of an ignition model and cannot find the part number you suggested. I have found a Bim024 which looks very similar but I am unsure on if will be a sufficient substitute. I have a Holden Hj one tonner in the build and am looking to run the vk efi manifold with vn gear and run a sc14 supercharger for a little more kick. What tune would be the best for this combination? And does anyone have the links for the mods for the ecu if I do the tuning myself. Thank you for the help.

Posts: 627
Joined: Tue Apr 21, 2015 1:42 pm

Re: How to convert a 202 to Delco

Postby heff0018 » Wed Oct 17, 2018 5:53 am

G,day there I have through all this and more, check out my Hemi 265 to EFI thread.

You will need an ECM Comms board and ECM NVRAM I got mine from the member Jayme. It comes with great instructions and if I can do it nearly anyone can.

If you can find a JE camira engine/efi loom it will make things real easy. Once you unwind all the insulation tape you can rejig the loom to fit a straight six configuration almost perfectly. You just need to grab two extra injector wires from a VN or similar and connect them in series to the existing injector wires. You just then need to hook the two earths to the block/head and the power and ground to the battery and your loom is powered.

You can use the camira ignition and most of the sensors if you get these with the loom.

I reckon I had similar problems finding the correct ignition module part number but it is out there.

Posts: 3
Joined: Sun Oct 14, 2018 5:27 pm
Location: Gin Gin Qld

Re: How to convert a 202 to Delco

Postby HoldenHj2001 » Wed Oct 17, 2018 7:35 am

Arh right I’ll go and have a look at the 265 thread then. Yea I might have to get onto the local wreckers and see if they have a je camira ecu sensors and loom. I can get the vn stuff really easy and I’m just wanting to do a straight forward conversion so I think the camira way will be easier. Thank you for your help heff.

Posts: 102
Joined: Mon Feb 26, 2018 4:18 pm
Location: Tasmania

Re: How to convert a 202 to Delco

Postby Comcal76 » Wed Oct 17, 2018 7:36 am


Posts: 627
Joined: Tue Apr 21, 2015 1:42 pm

Re: How to convert a 202 to Delco

Postby heff0018 » Wed Oct 17, 2018 7:44 pm

HoldenHj2001 wrote:Arh right I’ll go and have a look at the 265 thread then. Yea I might have to get onto the local wreckers and see if they have a je camira ecu sensors and loom. I can get the vn stuff really easy and I’m just wanting to do a straight forward conversion so I think the camira way will be easier. Thank you for your help heff.


They are getting harder to find these days but yes VN’s are everywhere. If you are good with auto electrics then it may be just as easy to use a VN loom.

You should create a new thread so as to keep all this important info in one thread.

Check out the getting started guide, the link is at the bottom on Holden202’s threads

Posts: 3
Joined: Sun Oct 14, 2018 5:27 pm
Location: Gin Gin Qld

Re: How to convert a 202 to Delco

Postby HoldenHj2001 » Sat Nov 03, 2018 5:12 pm

yea i can pick up a vn for next to nothing so i think thatll be the way. turns out you can still but the BIM148 module from Repco but at $100 roughly its worth looking for one imo. Yea i have read the getting started guide a multitude of times its alot of info to take in when your not looking at it in front of you. I think ill start a new thread when ive got all my parts here ready to go. Thanks :turbo: :punk:

Previous

Return to Delco ECU Conversions

Who is online

Users browsing this forum: No registered users and 1 guest