Page 16 of 24
Re: How to convert a 202 to Delco
Posted: Sun Jun 12, 2016 8:34 pm
by ballrash
cheers dylan well that sounds pretty straight forward. i'd say the camira module would be the easiest to setup so i'll see if i can track one down & plug to suit.
Appreciate the quick response.
Re: How to convert a 202 to Delco
Posted: Wed Dec 20, 2017 5:23 pm
by vkcalais202
Hello everyone,
Merry Christmas
I am looking a converting my 1985 VK Calais efi 202 to delco
Just to clarify I can use a JE Camira, LD Astra or N13 pulsar wiring loom as they are the same engine, Is this correct ?
Thankyou
vkcalais202
Re: How to convert a 202 to Delco
Posted: Thu Dec 21, 2017 10:53 am
by Holden202T
i dunno about the astra, but the other two yes.
Re: How to convert a 202 to Delco
Posted: Thu Dec 21, 2017 8:58 pm
by vkcalais202
Thanks Holden202T
I thought the Holden LD Astra was the same as a Nissan N13 pulsar (rebadged). Same as a Toyota Lexcen and Holden Commodore
The Nissan N13 pulsar is easier to find than the Holden JE camira in my area
They all have the Holden Family II 4cyl engine
Thanks
vkcalais202
Re: How to convert a 202 to Delco
Posted: Sun Dec 24, 2017 2:02 pm
by Holden202T
either way if you cant find them you can easily mod a V6 commodore loom.
Re: How to convert a 202 to Delco
Posted: Sun Dec 24, 2017 3:56 pm
by Charlescrown
I think the Pulsar has a longer loom with the ECU under the passengers seat. I personally would use a VN loom with 6 injector plugs and knock sensor wiring. It will need a bit of chopping and relay wiring though.
Re: How to convert a 202 to Delco
Posted: Wed Dec 27, 2017 2:36 pm
by antus
Yeah the LD astra is correct. In my area there are usually more N13 pulsars but any of the above will do. The 4 Cylinder EFI looms are seperate from the main loom so that is nice but you need to make sure you end up with the right connectors for the ignition module and right number of injectors.
Re: How to convert a 202 to Delco
Posted: Sat Dec 30, 2017 7:42 pm
by vkcalais202
Hi,
I picked up a JE Camira efi wiring loom, JE Camira ECU, some sensors and VN V6 throttle body today from Upullit Adelaide for $143
All I need to do now is the conversion and get the ECU remapped and I am good to go
Thanks
Michael
Re: How to convert a 202 to Delco
Posted: Sun Dec 31, 2017 9:08 am
by Holden202T
sweet that's a good start
theres a bin file in the custom tunes section for a stockish 202 with 808 ecu, it should get you started down the right path.
Re: How to convert a 202 to Delco
Posted: Sun Dec 31, 2017 6:43 pm
by vkcalais202
Hi,
A couple quick questions about the 202 delco conversion
1. When I am modifying the 202 distributor can I use the original factory pulse generator inside ?
2. The two black wires coming from the pulse generator, can they plug straight into the new ignition module mounted underneath the old one ?
I am sure there will be more questions to come as I go further into this project
Thanks
vkcalais202