Who would want wideband integration
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Who would want wideband integration
would that spare 5 volt input be on the pin above the pin the factory o2 goes into i here thats the spot.
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Who would want wideband integration
Yeah that would be the one. Pin D8 would be the likely input for a wideband, the factory narrowband O2 input is D7.delcowizzid wrote:would that spare 5 volt input be on the pin above the pin the factory o2 goes into i here thats the spot.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Who would want wideband integration
woot woot my JAW just arrived to begin testing busy day of soldering ahead we need a soldering smiley LOL. hopefully assembly goes sweet and be powering it up today.right time to find the instructions and begin
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Who would want wideband integration
Sounds like I will have to get cracking on the ECM code!!
We want pics of the JAW too
We want pics of the JAW too
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Who would want wideband integration
Well all assenbled no issues so yeah about to wire it up to some power for a test without the sensor then i better find somewhere to buy one i spose LOL.i am posting one pic as i will make a thread with a write up on the unit over the next few days and then further info when i get the sensor.so heres a pic .and VL400 will be ready to test that code when you get it done
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- antus
- Site Admin
- Posts: 8257
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Who would want wideband integration
looks good, looking forward to the review!
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Who would want wideband integration
im keen to see what the software can do!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
-
- Posts: 340
- Joined: Sat Mar 21, 2009 2:02 pm
- cars: VT S1 LS1 C/dore track car
HJ GTS Monaro Coupe
CV8 V2 S3
VE SSV
Re: Who would want wideband integration
Hey Delco.....i'm just wondering how you are going wire up the cigarette lighter into the heater circuit of that O2?
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Who would want wideband integration
yeah mario well from what i hear i may not need the lighter as the voltage reg gets just about hot enough to light a fag with but weall see how hot it gets.VL400 has a couple of ideas for modifying the circuit too stop the heat though so yeah might have to do some mods later on .you still got any sensors lying round over there for a broke delco hacker in need willing to part with some dollars just not heaps.finally got the software working my PC didnt like .net 2.0 for some reason but persistance payed off im going to start a thread on the JAW unit tonight just having a feed and sorting some people out then im on
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
- Posts: 345
- Joined: Sun Apr 05, 2009 1:07 pm
- cars: VN V6 Production Saloon
- Location: Gisborne NZ
Re: Who would want wideband integration
Following this with great interest Delco. though i must admit a fair chunk of it flies well over my head mate
Big step up from trying to look at a round guage whilst flooring it, dialing in opposite lock and avoiding swapping too much paint with the guy next to me.....ooooppps
Got a couple of Toyota (DENSO) four wire 02 sensors here, willing to bung one in the post if it helps.......after all this is a reciprocal back-scratching for the good of all kinda thing aint it
Big step up from trying to look at a round guage whilst flooring it, dialing in opposite lock and avoiding swapping too much paint with the guy next to me.....ooooppps
Got a couple of Toyota (DENSO) four wire 02 sensors here, willing to bung one in the post if it helps.......after all this is a reciprocal back-scratching for the good of all kinda thing aint it
Last edited by VNracer34G on Sat Apr 18, 2009 8:49 am, edited 1 time in total.
Build it, Race it, Break/Bend it ; Repeat.