OSEPlugin for Tunerpro 5 v1.80
-
- Posts: 2883
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: OSEPlugin for Tunerpro 5 v1.2.0
TP5 & maybe earlier too keep your last loaded log in the system & even if you uninstall & re-install it will keep finding it.
Up the top when tp5 opens does it show last xdl opened?
I'd try removing that or un select any open xdl's first.
Not sure as I'm not an expert by any means!
Up the top when tp5 opens does it show last xdl opened?
I'd try removing that or un select any open xdl's first.
Not sure as I'm not an expert by any means!
- vnsswithcam
- Posts: 79
- Joined: Sat Mar 20, 2010 1:20 pm
- cars: vt ss commodore
- Location: penrith n.s.w
Re: OSEPlugin for Tunerpro 5 v1.2.0
nah it cant be i havent logged on this laptop at all ive got another laptop that i data log with but im setting up this one to log and still nothin?
one point twenty one jiggawatts!!!! great scott!!!
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: OSEPlugin for Tunerpro 5 v1.2.0
i'd try deleting the tp5 config files and see if that helps, cause i think when you remove it they stay there!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vnsswithcam
- Posts: 79
- Joined: Sat Mar 20, 2010 1:20 pm
- cars: vt ss commodore
- Location: penrith n.s.w
Re: OSEPlugin for Tunerpro 5 v1.2.0
ok deleting config files didnt work but ive found an older version of tp5 5.0.6356.0 and installed that and boom its working like normal now?? no error message and i can see and use ose plugin now? i think im just going to use this setup until a newer version comes out my computer just doesnt want to agree with the latest version
one point twenty one jiggawatts!!!! great scott!!!
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: OSEPlugin for Tunerpro 5 v1.2.0
so 7330 isn't working for you ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vnsswithcam
- Posts: 79
- Joined: Sat Mar 20, 2010 1:20 pm
- cars: vt ss commodore
- Location: penrith n.s.w
Re: OSEPlugin for Tunerpro 5 v1.2.0
it looks that way? i havent changed anything else on my laptop but the version of tp5?
one point twenty one jiggawatts!!!! great scott!!!
-
- Posts: 340
- Joined: Sat Mar 21, 2009 2:02 pm
- cars: VT S1 LS1 C/dore track car
HJ GTS Monaro Coupe
CV8 V2 S3
VE SSV
Re: OSEPlugin for Tunerpro 5 v1.2.0
I've had the same problem too,a few weeks ago i asked a similar thing about the latest version and have had trouble with TP5 freezing up,or the bubble trace freezing in one spot.
Also rpm going crazy on dash display and bubble trace showing about 300rpm lower than actual rpm on the MAP display.
I haven't been playing since then as i put the boot into it on LPG and blew my masterpiece plenum box up like a balloon and blew the back panel away on the top and sides.
I thought my welds were suss but it showed a good 3/4 weld penetration.
Broke the welds clean.Everything was sealed too well.
Blew the VT rubber intake tube in bits,and blew the VN a/cleaner box off its clips.
The funniest part was because the air box is next to the LH guard it blew my Monaro badge clean off the guard,clips and all.
I noticed it the next day in the shed and thought "what the ? " and then worked it out.
I went for a walk where it happened and the badge was still on the side of the road.
I bent the back panel back as much as i could and used packing tape to seal it all and drive back home
First time in 3 years that its played up.
How do you post pics on here?
Also rpm going crazy on dash display and bubble trace showing about 300rpm lower than actual rpm on the MAP display.
I haven't been playing since then as i put the boot into it on LPG and blew my masterpiece plenum box up like a balloon and blew the back panel away on the top and sides.
I thought my welds were suss but it showed a good 3/4 weld penetration.
Broke the welds clean.Everything was sealed too well.
Blew the VT rubber intake tube in bits,and blew the VN a/cleaner box off its clips.
The funniest part was because the air box is next to the LH guard it blew my Monaro badge clean off the guard,clips and all.
I noticed it the next day in the shed and thought "what the ? " and then worked it out.
I went for a walk where it happened and the badge was still on the side of the road.
I bent the back panel back as much as i could and used packing tape to seal it all and drive back home
First time in 3 years that its played up.
How do you post pics on here?
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: OSEPlugin for Tunerpro 5 v1.2.0
Ahh man, sounds spectacular, but damn!
To post pics just attach them as files and they show in the thread.
To post pics just attach them as files and they show in the thread.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 340
- Joined: Sat Mar 21, 2009 2:02 pm
- cars: VT S1 LS1 C/dore track car
HJ GTS Monaro Coupe
CV8 V2 S3
VE SSV
Re: OSEPlugin for Tunerpro 5 v1.2.0
I bent it all back into shape and rewelded the back panel on.
This time i haven't done up the clamps as tight and left 3 clips on the airbox on.
This time i haven't done up the clamps as tight and left 3 clips on the airbox on.
- Attachments
-
- p6.JPG (67.26 KiB) Viewed 4964 times
-
- p1.JPG (60.31 KiB) Viewed 4964 times
-
- p2.JPG (83.27 KiB) Viewed 4964 times
-
- p5.JPG (86.64 KiB) Viewed 4964 times
-
- p4.JPG (69.49 KiB) Viewed 4964 times
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: OSEPlugin for Tunerpro 5 v1.2.0
thats one of the best efforts i've seen!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread