Page 27 of 97
Re: PCM Hammer - new ls1 flash tool
Posted: Mon Feb 11, 2019 6:12 am
by NSFW
The kernel and the app both need some additional code before we can write to a P59. But it's not a lot, so hopefully it won't be long.
I've tried reading two P59s, and succeeded with both, but there may be more work needed in that area too.
Re: PCM Hammer - new ls1 flash tool
Posted: Mon Feb 11, 2019 12:55 pm
by jlvaldez
This is nice. I'm following this thread, and looking for support to write to P59. Need to modify a few instructions to nops in the binary and flash it back to the CPU
Can read, but not yet write.
Re: PCM Hammer - new ls1 flash tool
Posted: Mon Feb 11, 2019 9:16 pm
by Gampy
NSFW wrote:The kernel and the app both need some additional code before we can write to a P59. But it's not a lot, so hopefully it won't be long.
I've tried reading two P59s, and succeeded with both, but there may be more work needed in that area too.
Well yabbering on here ain't gettin it done, lets go, chop chop chop, WTF you think this is a lax house! Ya got folx waitin on ya, get em all excited then drag them on and on ...
Re: PCM Hammer - new ls1 flash tool
Posted: Tue Feb 12, 2019 12:31 pm
by 160plus
So...since NSFW is clearly slacking in more then one dept. I'll just share this myself.
He showed me a picture yesterday that someone from the Corvette forums had taken were they altered a message in the DIC and ask'd me if I knew how the guy did it.....
Well I just so happen to have done a great deal of work on this and was happy to find a place that it could be used
[youtube]
https://www.youtube.com/watch?v=jO9VLo_cf8Y[/youtube]
Re: PCM Hammer - new ls1 flash tool
Posted: Wed Feb 13, 2019 5:40 am
by NSFW
I can't want wait see "It's Hammer Time" on my dashboard when the app starts reading or writing.
Re: PCM Hammer - new ls1 flash tool
Posted: Thu Feb 14, 2019 2:56 am
by vilefly
New guy here. Been in the field 25yrs, and remember when prom updates for 2.8L maf to speed density was all new.
Just reporting I had some success reading (only) using a snap-on Passthru pro and pcm hammer on a 09386530 pcm in a 2001 astro AWD van with a 4.3L. I had to relearn the passlock key (KOEO for 10min) after reading.
I need to confirm my read binary with a proper PCM mask. I doubt it, but will a 0411 mask work with this pcm binary?
Re: PCM Hammer - new ls1 flash tool
Posted: Thu Feb 14, 2019 3:11 am
by Gampy
Welcome,
Not quite sure what you mean by mask ...
However, I do believe that 9386530 number is the hardware number for a Service Number 12200411 pcm.
What is the OSID ?
It is the OSID that dictates much about the binary. Like the XDF to be use.
The OSID can be found in the logs ...
-Enjoy
Re: PCM Hammer - new ls1 flash tool
Posted: Thu Feb 14, 2019 3:35 am
by vilefly
Unfortunately, the logs don't seem to be stored anywhere. I will have to try again the next time I have time to play with this deadbeat customer's vehicle. The XDF was what I meant. I will try the 0411 xdf to see what I can see.
Re: PCM Hammer - new ls1 flash tool
Posted: Thu Feb 14, 2019 3:45 am
by DavidBraley
vilefly wrote:I will try the 0411 xdf to see what I can see.
You will need to use the correct xdf for the OSID in the 0411.
Re: PCM Hammer - new ls1 flash tool
Posted: Thu Feb 14, 2019 5:19 am
by Gampy
The logs are not stored ... They need to be copied and pasted to a text file whilst still in PcmHammer. (pasted into notepad for example)
If you have the .bin from a full read, you can PM it to me and I can get that info out of the binary for ya if you want.
-Enjoy