Pulling tune on DLTK chip
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Pulling tune on DLTK chip
So long as the bin still requires the security PAL we feel its ok to have it posted. It can help people see what gets tuned and Kalmaker can still get the royalties if someone would want to use the bin as posted.
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: Pulling tune on DLTK chip
Popped down to Jaycar n got a 40pin head and modded it to take the 32pin memcal no worries. Not too sure on the correct orientation of the memcal in relation to the MemprogL insertion socket so I read the chip both ways and saved them in both BIN form and HEX form each time. None of the 4 ways will open in Kalmaker and shows a "script not present" code for the BIN files and the HEX ones obviously (now ) show "binary file not present" code.
Any clues as to how to open this tune, that is if I've pulled the tune from the chip correctly
Any clues as to how to open this tune, that is if I've pulled the tune from the chip correctly
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: Pulling tune on DLTK chip
if you put the chip in wrong it could be buggered afterwards what size chip did you set it too read as well
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: Pulling tune on DLTK chip
Auto settings on everything. I put it in both ways doh
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: Pulling tune on DLTK chip
Oh, and which way is the right way again? The MemprogL is very generic and doesn't give any info in regards to this unfortunately
- Doctor Bob
- Posts: 195
- Joined: Mon Mar 02, 2009 10:58 pm
- cars: VN, VT
- Location: Melbourne Vic.
- Contact:
Re: Pulling tune on DLTK chip
unless you have it disabled the elnec software will check insertion etc before it does anything
pin 1 goes to the top, read it as a National 27c010
Rob
pin 1 goes to the top, read it as a National 27c010
Rob
- Doctor Bob
- Posts: 195
- Joined: Mon Mar 02, 2009 10:58 pm
- cars: VN, VT
- Location: Melbourne Vic.
- Contact:
Re: Pulling tune on DLTK chip
have a look at the pic beside the ZIF, it shows the device orientation
Re: Pulling tune on DLTK chip
if you look at the eprom there will be a small notch at one end for pin1.Match this with picture as dr bob said.
also if you have an aldl cable vl400s flash tool will detect kalmaker and read bin.
My Pm box is always open ,security pal or not.
also if you have an aldl cable vl400s flash tool will detect kalmaker and read bin.
My Pm box is always open ,security pal or not.
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: Pulling tune on DLTK chip
After checking the orientation re your guys suggestions it turns out that the memcal was inserted the correct way the 1st time I did a read and was saved as a BIN file. Still can't load it to the read buffer for viewing in kal. Any chance the original tuner has "locked" the tune? I thought that even if the user id was different I would still be able to peruse it in my read buffer while not connected to the ecu
Re: Pulling tune on DLTK chip
Post the bin and we will have a look.