Page 2 of 6
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 8:23 am
by Gampy
It appears we are using different xdf's.
Pretty sure mine is based on the one over at
Bored Truck Owners repository on GetHub, it is the only one I know of, there is no Advanced xdf.
I will check mine against it to be sure.
There are 129 total rows, all of them need to be flipped.
Just noticing the numbers are not exactly the same across the spread between the two, close though, they are definitely inverted.
My tools are having hex/decimal/imperial/metric conversion problems ... at math, I suck at best.
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 12:55 pm
by antus
I think the Board Truck Owner repo is dead. The owner has gone and he doesnt appear to be accepting pull requests. The content might have been mirrored in to the snowman repo, so that is the one to look in.
https://github.com/Snoman002/Engine-Tun ... e-TunerCat
See
viewtopic.php?f=42&t=6537&start=90#p103266 There is also a clone of the other repo too. Im struggling to navigate it, lots of structure, not as much content. Might need some work yet. Hmmm.
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 1:18 pm
by Gampy
Yea, two there, I'm going to have to do some comparing to figure out what one I have for sure ... Gonna take me a bit O time.
I need to know anyways ...
I do know it was the one from the PcmHacks repo.
I think it's 12587603_release.xdf from the Snowman repo.
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 3:48 pm
by Gampy
Ok, I am using this xdf:
12587603_RC1.xdf
And I have finally correctly extracted the exact data from your STOCK_2003 Tahoe 12579405.bin posted
here.
I can now repeat my steps on known data and it comes out correctly, so I am very confident it's 100% correct.
Sorry I have been so confusing, it has been a curve of education on my part ...
Paste this to the TunerPro table called: Primary Fuel Level Vs Fuel Gauge Sender A/D Counts
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
0.000000
1.126859
1.250689
1.374520
1.498351
2.001928
2.373420
2.749040
3.000829
3.376448
3.747940
4.251518
4.499179
5.498080
6.001658
6.373150
6.748769
7.248219
7.500008
7.999458
8.498909
9.501937
10.001387
10.500837
11.000287
11.499737
11.999188
12.498638
13.501666
14.001116
14.376736
15.000016
15.499467
16.250706
17.001945
17.501395
18.248506
18.999746
19.750985
20.250435
20.749885
21.249335
22.248236
22.999475
23.498925
23.998375
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
26.000304
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 7:49 pm
by yoheer
I use 2 xdfs
One is the same as you posted.
Second is 12587633_release.xdf from Snowman's repo. wich is full of comments and locked for editing with password
"Release" file has only one table Fuel gauge calibration
- 1.jpg (40.47 KiB) Viewed 4534 times
Concerning RC1 there is that table you told above.
it has 256 values
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 8:33 pm
by Gampy
PM'd it to you, didn't want to post it.
The error message is because it was saved as UTF-8, it must be RAW ASCII Text ... A modern editor issue.
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 8:51 pm
by Gampy
12587603_release.xdf is produced by user LRT, I do not support locked works ... Locked works are self centered, and not in the Spirit of Community.
Yes, that table in RC1 is the correct table, there are only 129 rows ... Notice the Counts jump by two.
However, you are seeing them in decimal, I see them in hex, I posted them in hex, it looks like you need them in decimal.
Maybe I need to learn more about TunerPro's settings.
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 9:12 pm
by yoheer
Thank you, i'll try
what about this table?
Fuel Gauge Sender Output %PWM Vs. % Fuel Level
Re: Fuel Gauge
Posted: Fri Nov 20, 2020 10:08 pm
by Gampy
This is what's in your Os 12579405 for that table and is also what I first posted.
100.000000
99.003906
84.902344
73.769531
64.003906
54.863281
45.703125
35.898438
24.902344
11.308594
0.000000
Re: Fuel Gauge
Posted: Thu Dec 03, 2020 5:52 am
by Vampyre
the file you got is probably from a van, it uses the same old school sender it always has that reads backward from 99 up gm vehicles, if you can find any other truck file with the same os and segment swap the system you will be good.
why did you os swap it to begin with ?? just wondering