pcmhacking.net

Nah, I've had several

Tazzi wrote:It hates life... I believe I have the first emo ECU.

But did it cut itself?


I did spam that command (100 times with 100ms delay) and switch ign input off and on while it was still hammering the CAN bus, figured i had nothing to loose.
 

Tazzi wrote:Im going to give a 0x0000 value a go which is the equivalent of this:
7E0 07 AE 7D 08 00 00 00 00

Whereas an ASCII 0000 immo code would look like this:
7E0 07 AE 7D 08 30 30 30 30

Is it just we use different methods for logging code/(programs for sending) and your string doesn't show the message length?

I did read through that thread before posting and saw what worked for me was slightly different

jxx wrote:

Tazzi wrote:Im going to give a 0x0000 value a go which is the equivalent of this:
7E0 07 AE 7D 08 00 00 00 00

Whereas an ASCII 0000 immo code would look like this:
7E0 07 AE 7D 08 30 30 30 30

Is it just we use different methods for logging code/(programs for sending) and your string doesn't show the message length?

I did read through that thread before posting and saw what worked for me was slightly different

Your logger outputs the 'frame size' straight after the CAN ID, this is not actually part of a CAN message but your logger is just indicating how much data has been sent.

So we have sent the same command, mine just doesnt work

Still seem to not be able to relink even after resetting the pim. Log below.

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - ECU is Seed/Key Unlocked
8 - Disconnect from MDI J2534 device
9 - Enable debug
10 - EXIT

Enter function to perform:3
Input Current PIM Pin Code:
6370

** Running PIM Reset Procedure **

** PIM Busy **

** Waiting **

** PIM Reset Successful **

Press any key to return to main menu



E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - ECU is Seed/Key Unlocked
8 - Disconnect from MDI J2534 device
9 - Enable debug
10 - EXIT

Enter function to perform:

E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - ECU is Seed/Key Unlocked
8 - Disconnect from MDI J2534 device
9 - Enable debug
10 - EXIT

Enter function to perform:2

Seed/Key Unlock Successful

** Requesting PIM Relink with ECU **
INFO: Buffer Empty No Response

** ECU/PIM Relink Procedure Failed **

Press any key to return to main menu

Can you retry with debug enabled? Wel see what it's saying

The1 wrote:Can you retry with debug enabled? Wel see what it's saying

Yeah will give it a shot tomorrow

E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - Run ECU Seed/Key Unlock
8 - Connect to J2534 device
9 - Enable debug
10 - EXIT

Enter function to perform:9

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - Run ECU Seed/Key Unlock
8 - Connect to J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:8
*********************************************************

Select Device:
*********************************************************
1 - MDI
2 - MDI 2
3 - Tech2
4 - VXDIAG

Input Device Number:1
DEBUG: Using DLL: C:\Program Files (x86)\GM MDI Software\Products\MDI\Dynamic Link Libraries\BVTX4J32.dll
DEBUG: Cable Connected: True

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - Run ECU Seed/Key Unlock
8 - Disconnect from MDI J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:2
DEBUG: SendMessage Response is
INFO: Buffer Empty No Response

** Requesting PIM Relink with ECU **
DEBUG: SendMessage Response is
INFO: Buffer Empty No Response


E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - Run ECU Seed/Key Unlock
8 - Disconnect from MDI J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:

Enter function to perform:9

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - Run ECU Seed/Key Unlock
8 - Disconnect from MDI J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:2
DEBUG: GetMessage response is 000007E8046701BA60000000
DEBUG: SendMessage Response is 6701BA60000000
DEBUG: Seed Received DEC: 47712 HEX: BA60
DEBUG: Calculated ECU Unlock Key DEC: 38444 HEX: 962C
DEBUG: GetMessage response is 000007E80267020000000000
DEBUG: SendMessage Response is 67020000000000
DEBUG: ECU Reply to Seed 67020000000000

Seed/Key Unlock Successful

** Requesting PIM Relink with ECU **
DEBUG: SendMessage Response is
INFO: Buffer Empty No Response


E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - ECU is Seed/Key Unlocked
8 - Disconnect from MDI J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:3
Input Current PIM Pin Code:
6370
DEBUG: Current PIM Pin 36 33 37 30

** Running PIM Reset Procedure **
DEBUG: GetMessage response is 00000644037F3B7800000000
DEBUG: SendMessage Response is 7F3B7800000000
DEBUG: SendMessage Response is 7F3B7800000000

** PIM Busy **

** Waiting **
DEBUG: Response After PIM Busy is 00000644027B607800000000

** PIM Reset Successful **

Press any key to return to main menu



E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - ECU is Seed/Key Unlocked
8 - Disconnect from MDI J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:

E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - ECU is Seed/Key Unlocked
8 - Disconnect from MDI J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:2
DEBUG: GetMessage response is 000007E8046701BA60000000
DEBUG: SendMessage Response is 6701BA60000000
DEBUG: Seed Received DEC: 47712 HEX: BA60
DEBUG: Calculated ECU Unlock Key DEC: 38444 HEX: 962C
DEBUG: GetMessage response is 000007E80267020000000000
DEBUG: SendMessage Response is 67020000000000
DEBUG: ECU Reply to Seed 67020000000000

Seed/Key Unlock Successful

** Requesting PIM Relink with ECU **
DEBUG: SendMessage Response is
INFO: Buffer Empty No Response
DEBUG: SendMessage Response is 00000490037F3BA336333730

** ECU/PIM Relink Procedure Failed **

Press any key to return to main menu



E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - ECU is Seed/Key Unlocked
8 - Disconnect from MDI J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:

E55Tool VZ V6 Tool V1.4

*********************************************************
Written By IronDuke & The1 pcmhacking.net
J2534 dll used from https://github.com/BrianHumlicek Modded By IronDuke

If this Program Saved you Time/Money then Please Donate

Paypal nigel@eyeit.org for Further Devs

*********************************************************
************** E55Tool VZ V6 Main Menu ****************
*********************************************************
1 - ECU Bruteforce Pin Reset Menu
2 - ECU/PIM Relink
3 - Reset PIM
4 - Write VIN
5 - ECU Information
6 - Advanced Menu
7 - ECU is Seed/Key Unlocked
8 - Disconnect from MDI J2534 device
9 - Disable debug
10 - EXIT

Enter function to perform:2
DEBUG: GetMessage response is 000007E8046701BA60000000
DEBUG: SendMessage Response is 6701BA60000000
DEBUG: Seed Received DEC: 47712 HEX: BA60
DEBUG: Calculated ECU Unlock Key DEC: 38444 HEX: 962C
DEBUG: GetMessage response is 000007E80267020000000000
DEBUG: SendMessage Response is 67020000000000
DEBUG: ECU Reply to Seed 67020000000000

Seed/Key Unlock Successful

** Requesting PIM Relink with ECU **
DEBUG: SendMessage Response is
INFO: Buffer Empty No Response
DEBUG: SendMessage Response is 00000490037F3BA336333730

** ECU/PIM Relink Procedure Failed **

Press any key to return to main menu

ecu is reset? Pim at the end is saying 7F access denied, im not sure if the pim has a timer or not ive had something similar before and after retrying while leaving the pim in a reset state for an hour it then worked.