Re: VE V6 ECU LINKER
Posted: Sun Feb 06, 2022 3:07 pm
While testing on an E39 today i noticed if you turn the ignition off for 20 seconds then on again after a reset or link it saves to flash.
pcmhacking.net
Electronic Fuel Injection - Developement & Tuning
https://pcmhacking.net/forums/
Ve Software
Page 7 of 9
Re: VE V6 ECU LINKER
Posted: Sun Feb 06, 2022 8:16 pm
i think the relink worked on both your tool and tech2 for this E69 VE, this car has other issues, it's cranking and no dash messages other than stability issue (prob rear sensor as known) so it should run, ive read in quite a few places that the "P0633 Immobilizer Key Not Programmed – ECM/PCM" is logged after relinking and goes out once engine is started. I have other fault codes coming up now on this car P0197,118,193,222,122 so ill be chasing down another circuit, this car blew the capacitor off the circuit board on the battery terminals inside the ecu and blew the F35 20amp odd coil circuit fuse.
Re: VE V6 ECU LINKER
Posted: Thu Feb 10, 2022 8:26 am
Car is up and running, both tools working successfully on E69
Re: VE V6 ECU LINKER
Posted: Fri Apr 01, 2022 4:57 pm
*1/04/22 V0.02
-Added HVAC Single/Dual Zone programming
-Added SIC Sports/Standard mode programming and Vin read/write
-Added HVAC Single/Dual Zone programming
-Added SIC Sports/Standard mode programming and Vin read/write
Re: VE V6 ECU LINKER
Posted: Fri Apr 15, 2022 3:40 pm
V0.04
-Added IPC Config Programming
Went onsite to do an IPC and EHU
Neither Tech2, Autel or Launch could change EBCM type in the IPC
To get the job done i used my SWCAN VIN programmer for seed key unlock and launch for the config programming
So added the function today
-Added IPC Config Programming
Went onsite to do an IPC and EHU
Neither Tech2, Autel or Launch could change EBCM type in the IPC
To get the job done i used my SWCAN VIN programmer for seed key unlock and launch for the config programming
So added the function today
- IPC.png (17.37 KiB) Viewed 10271 times
Re: VE V6 ECU LINKER
Posted: Sat Apr 16, 2022 11:45 am
Have you uploaded a download link for V0.04?mattyjf01 wrote:V0.04
-Added IPC Config Programming
Went onsite to do an IPC and EHU
Neither Tech2, Autel or Launch could change EBCM type in the IPC
To get the job done i used my SWCAN VIN programmer for seed key unlock and launch for the config programming
So added the function today
Re: VE V6 ECU LINKER
Posted: Thu Apr 21, 2022 1:18 pm
Looks awesome!
I have a VE that I am currently converting from V6 to V8.
Perfect candidate to test your software on.
Has the download link been shared yet?
I have a VE that I am currently converting from V6 to V8.
Perfect candidate to test your software on.
Has the download link been shared yet?
Re: VE V6 ECU LINKER
Posted: Thu Apr 21, 2022 1:22 pm
The free demo version isUCMatt wrote:Looks awesome!
I have a VE that I am currently converting from V6 to V8.
Perfect candidate to test your software on.
Has the download link been shared yet?
Re: VE V6 ECU LINKER
Posted: Sun Apr 24, 2022 4:18 pm
Like I've done with the VZ software I'm adapting it to ELM327 USB and Bluetooth
Here are ones that don't work out of the box
The Best one I've found is the forscan with the high/low switch which can be easily modified to be CAN/SWCAN
Swap pin 3 -> 1
Swap pin 11 -> 4 (I connected it to 4 and 5)
Swapped
Here are ones that don't work out of the box
Swap pin 11 -> 4 (I connected it to 4 and 5)
Re: VE V6 ECU LINKER
Posted: Sun Apr 24, 2022 4:30 pm
Home Workstation
Taking over the lounge room (The wife loves it)
Taking over the lounge room (The wife loves it)