LS1 Boost OS V3
Posted: Fri Apr 07, 2023 2:28 pm
Version 3 of the LS1 Boost OS
Notes:
1. Many new features were added since the V2 release. See below for the full feature set.
2. Boost OS Patcher was created by me to help assist with patching, upgrades, bug fixes, and the ability to revert to a prior version or even back to the factory OS.
3. Only PCM Hammer V20 is compatible since V21 is not aware of this OSID and the new parameter section. All changes to Boost OS parameters must be flashed via Write OS, Calibration, and Boot.
4. This software has been tested by a number of people including myself, so if you are having issues please verify there are no mechanical or tuning issues prior to posting bug reports.
5. Feature Ideas and Development Discussion Here -> LS1 Boost OS - Development.
Current Features:
N/A, 2 bar, or 4 bar VE Table
Boost Spark Adder
Open Loop Boost Control
Wideband Closed Loop Fueling
Launch Control
Flat Foot Shift
Spark Cut Engine Speed Limiter
Desired Air/Fuel Ratio (Replaces Power Enrichment)
Supported Operating Systems:
P59:
12587603
How to Upgrade to LS1 Boost OS:
1. Download Latest TunerPro Version, PCM Hammer V20, attached zip file (includes TunerPro DLL, Boost OS V3 XDF, and Boost OS Patcher)
Note: Ensure DLL file in TunerPro Directory "\Documents\TunerPro Files\Plugins"
2. Open Boost OS Patcher.exe
3. Enter input file name. (e.g. "MyFile.bin" and the bin file must be in the same directory/folder as the Boost OS Patcher.exe)
4. Select an OS version to apply. (Recommended to Apply the Highest Version)
Note: When upgrading all parameters are given default values with all features disabled.
5. Enter the output file name. (e.g. "MyNewFile.bin")
6. Make enable features and make tune changes in TunerPro with the XDF from the zip file.
7. Flash tune to PCM. (You must flash in PCM Hammer V20 via Tools -> Write OS, Calibration, and Boot)
Want To Show Appreciation & Help Support Development?
Consider joining my Patreon where V4 is currently posted.
Here is a video going over the process of patching and a review of all the features for V3 & V4: YouTube Video
Thanks,
Branden
Notes:
1. Many new features were added since the V2 release. See below for the full feature set.
2. Boost OS Patcher was created by me to help assist with patching, upgrades, bug fixes, and the ability to revert to a prior version or even back to the factory OS.
3. Only PCM Hammer V20 is compatible since V21 is not aware of this OSID and the new parameter section. All changes to Boost OS parameters must be flashed via Write OS, Calibration, and Boot.
4. This software has been tested by a number of people including myself, so if you are having issues please verify there are no mechanical or tuning issues prior to posting bug reports.
5. Feature Ideas and Development Discussion Here -> LS1 Boost OS - Development.
Current Features:
N/A, 2 bar, or 4 bar VE Table
Boost Spark Adder
Open Loop Boost Control
Wideband Closed Loop Fueling
Launch Control
Flat Foot Shift
Spark Cut Engine Speed Limiter
Desired Air/Fuel Ratio (Replaces Power Enrichment)
Supported Operating Systems:
P59:
12587603
How to Upgrade to LS1 Boost OS:
1. Download Latest TunerPro Version, PCM Hammer V20, attached zip file (includes TunerPro DLL, Boost OS V3 XDF, and Boost OS Patcher)
Note: Ensure DLL file in TunerPro Directory "\Documents\TunerPro Files\Plugins"
2. Open Boost OS Patcher.exe
3. Enter input file name. (e.g. "MyFile.bin" and the bin file must be in the same directory/folder as the Boost OS Patcher.exe)
4. Select an OS version to apply. (Recommended to Apply the Highest Version)
Note: When upgrading all parameters are given default values with all features disabled.
5. Enter the output file name. (e.g. "MyNewFile.bin")
6. Make enable features and make tune changes in TunerPro with the XDF from the zip file.
7. Flash tune to PCM. (You must flash in PCM Hammer V20 via Tools -> Write OS, Calibration, and Boot)
Want To Show Appreciation & Help Support Development?
Consider joining my Patreon where V4 is currently posted.
Here is a video going over the process of patching and a review of all the features for V3 & V4: YouTube Video
Thanks,
Branden