Delco OSE FlashTool V1.51
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: The FlashTool V1.15
when the aldl passthrough is added to the flashtool that will allow tp4 and scanner pro to work together ... otherwise you still need to use the dos based antusprom
if antus can work out a plugin for TP5 there may be a light at the end of that tunnel too ... but that ain't going to happen for a while!
if antus can work out a plugin for TP5 there may be a light at the end of that tunnel too ... but that ain't going to happen for a while!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: The FlashTool V1.15
Have loaded flashtool v1.15 & started emulation. received cal from ecu & initialised TP5, flashtool "READY" & "TP Found" boxes are both illuminated. TP5 logging not working, clicking "acquire data connect/disconnect" has no effect. TP5 logging is ok if I use dos version of antusprom. what have I missed.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: The FlashTool V1.15
you have missed the part where we said logging doesn't work. only changing xdf data in TP5 will work with that connection.
If you want to log and change xdf data at the same time the dos antusprom is the only option.
If you want to log and change xdf data at the same time the dos antusprom is the only option.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- antus
- Site Admin
- Posts: 8253
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: The FlashTool V1.15
Note: To connect to an OSE v1.0.1 bin in a car with no BCM you must make sure "Options/Preferences/DisableBCM Chatter" is NOT selected.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: The FlashTool V1.15
Just checking to see if their was any further development with the logging tuning via usb aldl or tunerpro 5 integration.
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: The FlashTool V1.15
No, nothing further has been done with this. Once TP5's plug-ins are working something will be written to use that. Will make it much easier to setup too.
Re: The FlashTool V1.15
Hi,
I am using autoprom and successfully connected to ecm , read cal etc with no problems. But when trying to modify xdf in the flex output editor I get a unknown error when writing xdf . green status blocks seem to get 3/4 of the way ...
any ideas ?
I am using autoprom and successfully connected to ecm , read cal etc with no problems. But when trying to modify xdf in the flex output editor I get a unknown error when writing xdf . green status blocks seem to get 3/4 of the way ...
any ideas ?
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: The FlashTool V1.15
Can you email me the XDF? If I can reproduce the error should be able to fix it.
Re: The FlashTool
I apologize in advance for my english. I have a question.VL400 wrote: * Note - VS Ecotec and newer PCMs that have a 128k binary use a memory bank switching method.
The flash tool only supports reading and writing to bank 1, the first 64k. This means the 'Get Bin'
function does not get the entire binary.
I know that my firmware is located in the 2 bank, 64k to the second (starting with address 8000 and end. 32k). Can I read them your program.
-
- Posts: 440
- Joined: Sun Mar 22, 2009 11:52 am
- cars: VT V6 supercharged in a corolla
- Location: Sydney
- Contact:
Re: The FlashTool V1.18
Hi malser. If you want to read from 0 to FFFF (64k) this program will work. You won't be able to read from 10,000 to 1FFFF
Cheers
Richard
Cheers
Richard