Page 1 of 1

Can't read P59 using PCM Hammer

Posted: Sun Jun 04, 2023 9:56 am
by Thorwon
I have a P59 I'm running my Jeep MJ with. I was going to read it to day so I could play with the tune a little. It connects ok but will not read entire.
Anyway here are the logs.
Can someone tell me what's wrong? I've read and written to this PCM many times and never had any issues.

Debug log

[07:37:30:102] PCM Hammer 021.2
[07:37:30:119] Saturday, June 03 2023 @07:37:30:11
[07:37:30:132] ElmDevice initialization starting.
[07:37:30:147] TX:
[07:37:30:168] TX: AT Z
[07:37:30:201] ELM327 v2.1
[07:37:30:203] TX: AT E0
[07:37:30:216] AT E0 OK
[07:37:30:218] TX: AT S0
[07:37:30:232] OK
[07:37:30:234] TX: AT RV
[07:37:30:246] Voltage: 12.7V
[07:37:30:253] TX: AT I
[07:37:30:272] Elm ID: ELM327 v2.1
[07:37:30:282] Initializing PcmHacking.AllProDeviceImplementation
[07:37:30:283] TX: AT #1
[07:37:30:305] All Pro ID: Copyright (c) 2009-2018 ObdDiag.Net This is free software; see the source for copying conditions.
[07:37:30:312] TX: AT #3
[07:37:30:329] All Pro self test result: PWM wiring is OK VPW wiring is OK ISO9141/14230 wiring is OK CAN wiring is OK
[07:37:30:317] Unable to retrieve help.html from network: HTTP NotFound.
[07:37:30:318] Unable to retrieve credits.html from network: HTTP NotFound.
[07:37:30:319] Unable to retrieve start.txt from network: HTTP NotFound.
[07:37:30:336] TX: AT @1
[07:37:30:341] Loaded help.html from cache.
[07:37:30:342] Loaded credits.html from cache.
[07:37:30:343] Loaded start.txt from cache.
[07:37:30:350] Thanks for using PCM Hammer.
[07:37:30:591] All Pro firmware: 1.22
[07:37:30:600] TX: AT AL
[07:37:30:758] OK
[07:37:30:760] TX: AT SP2
[07:37:30:769] OK
[07:37:30:770] TX: AT DP
[07:37:30:781] SAE J1850 VPW
[07:37:30:782] TX: AT AR
[07:37:30:786] OK
[07:37:30:787] TX: AT AT0
[07:37:30:791] OK
[07:37:30:792] TX: AT SR F0
[07:37:30:802] OK
[07:37:30:802] TX: AT H1
[07:37:30:806] OK
[07:37:30:807] TX: AT ST 20
[07:37:30:812] OK
[07:37:56:954] Will save to C:\Users\Owner\Documents\MJ new reads\6-3-2023\test read.bin
[07:38:00:400] Querying operating system of current PCM.
[07:38:00:431] Setting timeout for ReadProperty, 25 ms.
[07:38:00:436] TX: AT ST 06
[07:38:00:442] OK
[07:38:00:473] TX: AT SH 6C 10 F0
[07:38:00:478] Set header response: OK
[07:38:00:481] TX: 3C0A
[07:38:00:572] RX: 6C F0 10 7C 0A 00 C0 12 53
[07:38:00:576] OSID: 12587603
[07:38:00:594] Suppressing VPW chatter.
[07:38:00:595] TX: AT SH 6C FE F0
[07:38:00:601] Set header response: OK
[07:38:00:602] TX: 2800
[07:38:00:652] RX: 6C F0 10 68 00
[07:38:00:660] Sending 'test device present' notification.
[07:38:00:663] Setting timeout for Minimum, 0 ms.
[07:38:00:665] TX: AT ST 01
[07:38:00:672] OK
[07:38:00:674] TX: AT SH 8C FE F0
[07:38:00:681] Set header response: OK
[07:38:00:684] TX: 3F
[07:38:00:699] Setting timeout for ReadProperty, 25 ms.
[07:38:00:701] TX: AT ST 06
[07:38:00:708] OK
[07:38:00:715] Ignoring chatter: 6C F0 10 68 00
[07:38:00:725] Sending seed request.
[07:38:00:728] TX: AT SH 6C 10 F0
[07:38:00:733] Set header response: OK
[07:38:00:735] TX: 2701
[07:38:00:778] RX: 6C F0 10 67 01 1C 82
[07:38:00:779] Parsing seed value.
[07:38:00:798] Sending unlock request (1C82, 1131)
[07:38:00:800] TX: 27021131
[07:38:00:840] RX: 6C F0 10 67 02 34
[07:38:00:845] Unlock succeeded.
[07:38:00:887] Sending 'test device present' notification.
[07:38:00:889] Setting timeout for Minimum, 0 ms.
[07:38:00:891] TX: AT ST 01
[07:38:00:897] OK
[07:38:00:899] TX: AT SH 8C FE F0
[07:38:00:905] Set header response: OK
[07:38:00:906] TX: 3F
[07:38:00:920] Setting timeout for ReadProperty, 25 ms.
[07:38:00:921] TX: AT ST 06
[07:38:00:926] OK
[07:38:00:933] Attempting switch to VPW 4x
[07:38:00:945] TX: AT SH 6C FE F0
[07:38:00:950] Set header response: OK
[07:38:00:951] TX: A0
[07:38:00:989] RX: 6C F0 10 E0 AA
[07:38:00:990] Parsing 6C F0 10 E0 AA
[07:38:00:996] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[07:38:01:008] Sending 'test device present' notification.
[07:38:01:010] Setting timeout for Minimum, 0 ms.
[07:38:01:011] TX: AT ST 01
[07:38:01:017] OK
[07:38:01:019] TX: AT SH 8C FE F0
[07:38:01:025] Set header response: OK
[07:38:01:026] TX: 3F
[07:38:01:038] Setting timeout for ReadProperty, 25 ms.
[07:38:01:040] TX: AT ST 06
[07:38:01:045] OK
[07:38:02:199] Timeout during receive.
[07:38:02:204] Sending 'test device present' notification.
[07:38:02:209] Setting timeout for Minimum, 0 ms.
[07:38:02:213] TX: AT ST 01
[07:38:02:222] OK
[07:38:02:225] TX: 3F
[07:38:02:243] Setting timeout for ReadProperty, 25 ms.
[07:38:02:246] TX: AT ST 06
[07:38:02:255] OK
[07:38:02:258] TX: AT SH 6C FE F0
[07:38:02:266] Set header response: OK
[07:38:02:269] TX: A1
[07:38:03:338] Timeout during receive.
[07:38:03:359] AllPro setting VPW 4X
[07:38:03:363] TX: AT VPW4
[07:38:03:370] OK
[07:38:03:372] Sending 'test device present' notification.
[07:38:03:375] Setting timeout for Minimum, 0 ms.
[07:38:03:378] TX: AT ST 01
[07:38:03:384] OK
[07:38:03:387] TX: AT SH 8C FE F0
[07:38:03:394] Set header response: OK
[07:38:03:397] TX: 3F
[07:38:03:404] Unexpected response to message content: BUS BUSY
[07:38:03:407] Setting timeout for ReadProperty, 12 ms.
[07:38:03:410] TX: AT ST 03
[07:38:03:416] OK
[07:38:03:427] Sending 'test device present' notification.
[07:38:03:430] Setting timeout for Minimum, 0 ms.
[07:38:03:433] TX: AT ST 01
[07:38:03:441] OK
[07:38:03:444] TX: 3F
[07:38:03:451] Unexpected response to message content: BUS BUSY
[07:38:03:454] Setting timeout for ReadProperty, 12 ms.
[07:38:03:457] TX: AT ST 03
[07:38:03:463] OK
[07:38:03:482] Loaded C:\Users\Owner\Documents\PcmHammer021.2\PcmHammer021.2\Kernel-P01.bin
[07:38:03:511] Sending upload request for kernel size 7890, loadaddress FF8000
[07:38:03:517] TX: AT SH 6C 10 F0
[07:38:03:522] Set header response: OK
[07:38:03:523] TX: 34001000FF8000
[07:38:03:529] Unexpected response to message content: BUS BUSY
[07:38:03:530] Send failed. Attempt #1
[07:38:03:531] TX: 34001000FF8000
[07:38:03:537] Unexpected response to message content: BUS BUSY
[07:38:03:538] Send failed. Attempt #2
[07:38:03:540] Permission to upload kernel was denied.
[07:38:03:547] If this persists, try cutting power to the PCM, restoring power, waiting ten seconds, and trying again.
[07:38:03:554] Failed to upload kernel to PCM
[07:38:03:563] Halting the kernel.
[07:38:03:567] TX: 20
[07:38:03:584] AllPro setting VPW 1X
[07:38:03:585] TX: AT VPW1
[07:38:03:590] OK
[07:38:03:591] TX: 20
[07:38:03:621] Clearing trouble codes.
[07:38:03:635] Setting timeout for Minimum, 0 ms.
[07:38:03:637] TX: AT ST 01
[07:38:03:643] OK
[07:38:03:900] TX: AT SH 68 6A F0
[07:38:03:911] Set header response: OK
[07:38:03:916] TX: 04
[07:38:04:196] TX: 04
[07:38:04:478] TX: AT SH 8C FE F0
[07:38:04:488] Set header response: OK
[07:38:04:494] TX: 14
[07:38:04:775] TX: 14
[07:38:04:802] Elapsed time 00:00:03.9446548
[07:38:04:835] Read failed, Error

Results

[07:37:30:102] PCM Hammer 021.2
[07:37:30:119] Saturday, June 03 2023 @07:37:30:11
[07:37:30:246] Voltage: 12.7V
[07:37:30:272] Elm ID: ELM327 v2.1
[07:37:30:305] All Pro ID: Copyright (c) 2009-2018 ObdDiag.Net This is free software; see the source for copying conditions.
[07:37:30:329] All Pro self test result: PWM wiring is OK VPW wiring is OK ISO9141/14230 wiring is OK CAN wiring is OK
[07:37:30:350] Thanks for using PCM Hammer.
[07:37:30:591] All Pro firmware: 1.22
[07:37:56:954] Will save to C:\Users\Owner\Documents\MJ new reads\6-3-2023\test read.bin
[07:38:00:400] Querying operating system of current PCM.
[07:38:00:576] OSID: 12587603
[07:38:00:845] Unlock succeeded.
[07:38:00:933] Attempting switch to VPW 4x
[07:38:00:996] Module 0x10 (engine controller) has agreed to enter high-speed mode.
[07:38:03:540] Permission to upload kernel was denied.
[07:38:03:547] If this persists, try cutting power to the PCM, restoring power, waiting ten seconds, and trying again.
[07:38:03:554] Failed to upload kernel to PCM
[07:38:03:621] Clearing trouble codes.
[07:38:04:802] Elapsed time 00:00:03.9446548
[07:38:04:835] Read failed, Error

Re: Can't read P59 using PCM Hammer

Posted: Sun Jun 04, 2023 12:11 pm
by antus
It looks like 4x speed isnt working properly, try changing the settings and read it at 1x. the all pro ended up being a bit hit and miss before they dissappeared. nsfw was only able to get his to work at 4x when he had an obd2 double adapter cable inline. Whether you wa t to try random stuff like that or just use 1x is up to you.

Re: Can't read P59 using PCM Hammer

Posted: Sun Jun 04, 2023 12:20 pm
by Thorwon
antus wrote:It looks like 4x speed isnt working properly, try changing the settings and read it at 1x. the all pro ended up being a bit hit and miss before they dissappeared. nsfw was only able to get his to work at 4x when he had an obd2 double adapter cable inline. Whether you wa t to try random stuff like that or just use 1x is up to you.
Ok, I'll try 1x.