delco into Td gemini running Mitsubishi 6A12 TT
Re: delco into Td gemini running Mitsubishi 6A12 TT
I'll post up some pics when the engine gets here
Re: delco into Td gemini running Mitsubishi 6A12 TT
engine's here, pics tomorrow, already started picking it to bits.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: delco into Td gemini running Mitsubishi 6A12 TT
haha nice one mate
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: delco into Td gemini running Mitsubishi 6A12 TT
removing all the crap I'm not using
the turbo's are coming off too, their so small it's embarassing so I'm switching to a big single.
the turbo's are coming off too, their so small it's embarassing so I'm switching to a big single.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: delco into Td gemini running Mitsubishi 6A12 TT
looks like a marvelous place for the thermostat once its in the gem mate .bet it goes like a scalded cat too.
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: delco into Td gemini running Mitsubishi 6A12 TT
interior fan has been removed, will notch out a little of the firewall if I need to.
I have shite loads of stainless pipe for routing the coolant from the radiator.
I have shite loads of stainless pipe for routing the coolant from the radiator.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: delco into Td gemini running Mitsubishi 6A12 TT
thats a big top end!!! lucky theres plenty of room in the gem bay .... will the brake booster/master be an issue ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: delco into Td gemini running Mitsubishi 6A12 TT
nah, theres plenty of room.
with the turbo manifolds removed and all the other useless cluttering crap removed the top end is only 600mm wide.
thats smaller than a vg30 engine and the vg30 fits quite nicely.
with the turbo manifolds removed and all the other useless cluttering crap removed the top end is only 600mm wide.
thats smaller than a vg30 engine and the vg30 fits quite nicely.
Re: delco into Td gemini running Mitsubishi 6A12 TT
well the gem is home, time for some work to get done.
with a little luck we'll be bolting up the transmission tomorrow, and if I get a crane on short notice dropping the box and motor into the car for the initial fit up.
she's good, cheers mate!
we found some welsh plugs on the front of the heads, we can block off the thermostat holes on the back and relocate the lot to the front of the engine.
I'm going to piss of the use of an actual thermostat and run a davies craig pump, all sorted.
with a little luck we'll be bolting up the transmission tomorrow, and if I get a crane on short notice dropping the box and motor into the car for the initial fit up.
she's good, cheers mate!
we found some welsh plugs on the front of the heads, we can block off the thermostat holes on the back and relocate the lot to the front of the engine.
I'm going to piss of the use of an actual thermostat and run a davies craig pump, all sorted.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: delco into Td gemini running Mitsubishi 6A12 TT
you get a feel for how big the motor is compared to the car when they are in the same picture together
keen to see some progress pics .. am in sure you are
keen to see some progress pics .. am in sure you are
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread