nope not yet have ran in to a few problems
the hardware connects ok
blank checks ok
i go to wright to the chip and it cracks up with some error
i cant remember what it is some buffer thing
i will keep playing
willem programmer help
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: willem programmer help
what chips are you using 29C256 or 27SF512 electronic erase or UV erase 27C256 etc.i dont even blank check nowdays just give the uv erase ones 5-6 mins in the eraser and burn them.is it saying that the chip and buffer dont match at a certian location in red down the bottom when you goto burn the eprom.is it a brandnew eprom too cause i just got a heap of new ones and they must be coated on the legs with something and dont burn without scraping the sides of the legs that touch the ZIF in the willem first with a knife to remove whatever is on the legs
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- antus
- Site Admin
- Posts: 8272
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: willem programmer help
Looks like either your chip is not erase properly or is dead, or your adapter has a short or no-connection somewhere. Ive seen similar results a few times doing the same thing with an adaptor and double checking the connections everywhere found a fault each time. In my case mostly over heated chips dropping lines between the IC and the chip legs, or a data or address line not making connection. Get a multimeter and check continuity from each leg on the chip to the leg on the end of your adapter. At the same time check non-continuity to the next leg along (no shorts). good luck!
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: willem programmer help
GOT IT
burnt then read back off the chip
compared to the origanl bin in tuner pro and shes all good
just wish i had the car going to try it out
burnt then read back off the chip
compared to the origanl bin in tuner pro and shes all good
just wish i had the car going to try it out
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: willem programmer help
sweet all go now comes the fun
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10328
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: willem programmer help
well brooksy get out there and get it running mate hahaha
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- antus
- Site Admin
- Posts: 8272
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: willem programmer help
sweet
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396