LS1 Boost OS - Development

turbo_v6 · Post by **turbo_v6** » Fri May 28, 2021 1:08 am

Stokes1114 wrote:I could test here in a week. I have a spare with 2156 already on it.

Ok! If you upload your tune (.bin) I can apply my patch and put in a base tune that should run and drive. It may not be perfect, but it would be good enough to test.

kojab · Post by **kojab** » Fri May 28, 2021 9:09 am

I am currently using HPT 1260001 3bar bin. Spark table runs out as you know at 1.2 grams/cyl approx 8 PSI boost. Been trying to fudge it for a while.
My new engine was built to handle at least 25 pounds of boost.

I could transfer my current settings into a 12212156 OS bin and test your new "LS1 Boost OS" which would be very interesting.

I do all my own tuning and have been doing so for the last 30 years. I can give you feed back on my progress.

Stokes1114 · Post by **Stokes1114** » Sat May 29, 2021 12:30 pm

I haven't transferred any of my settings to this bin from my 6125 yet. Just let me know if there's anything I shouldn't mess with.

turbo_v6 · Post by **turbo_v6** » Mon May 31, 2021 12:34 pm

Stokes1114 wrote:I haven't transferred any of my settings to this bin from my 6125 yet. Just let me know if there's anything I shouldn't mess with.

If possible I would like to start with a bin that was confirmed running so that the number of changes are reduced. Also what is the 6125 OS?

kojab · Post by **kojab** » Mon May 31, 2021 12:40 pm

I am still converting my HPT 1260001 3bar bin to 12212156. Spent a day yesterday getting most of it done. Hope to test it running on the road later today.

turbo_v6 · Post by **turbo_v6** » Mon May 31, 2021 12:47 pm

kojab wrote:I am still converting my HPT 1260001 3bar bin to 12212156. Spent a day yesterday getting most of it done. Hope to test it running on the road later today.

Ok perfect! Also what cable will you be using to flash the bin? HPTuners won't allow you to flash a raw bin file.

kojab · Post by **kojab** » Mon May 31, 2021 1:09 pm

bubba2533 wrote:
kojab wrote:I am still converting my HPT 1260001 3bar bin to 12212156. Spent a day yesterday getting most of it done. Hope to test it running on the road later today.
Ok perfect! Also what cable will you be using to flash the bin? HPTuners won't allow you to flash a raw bin file.

Probably EFILive a early version.

Should I send the modified 12212156 bin to you directly?

turbo_v6 · Post by **turbo_v6** » Mon May 31, 2021 1:40 pm

Yeah you can pm it to me when you’re done

Stokes1114 · Post by **Stokes1114** » Mon May 31, 2021 4:16 pm

No problem I'll make my changes and test in the am. 6125 is the p01 flex fuel os. Came stock on my truck.

turbo_v6 · Post by **turbo_v6** » Tue Jun 01, 2021 1:18 am

Year, make, model of your truck? And what’s the full OS ID? I might take a look at that OS so the P01 folks can have flex fuel.

LS1 Boost OS - Development

Re: LS1 Boost OS

Re: LS1 Boost OS

Re: LS1 Boost OS

Re: LS1 Boost OS

Re: LS1 Boost OS

Re: LS1 Boost OS

Re: LS1 Boost OS

Re: LS1 Boost OS

Re: LS1 Boost OS

Re: LS1 Boost OS