Vlad's rides thread

Post Your Delco Powered Ride Here
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Vlad's rides thread

Post by vlad01 »

Yep, biggest leak by far is the quarter glass. They pour water in when they perish.

This wasn't actually leaking on the white car, but was going to sooner or later. On the shitbox, it was merely a weep and that car I think was the worst case, as you can see it's seal was total trash and yet the leaking was very minimal. Lucky to be a teaspoon after a long days rain and only some days, not all days that rained.

You can certainly make some seals from self adhesive foam rubber from Clark Rubber. I recommend the neoprene foam self adhesive rolls there. You'll probably have to cut them down to the right width. I get the 50mm wide so I can make most seals as I need.

I actually just bought brand new vents since I got them for about $40 each, mainly to save time and piss farting around making seals. I have less energy these days and new vents were available for a price I was willing to trade money for not having to expend physical and mental effort for. You can't by the seals separate, they come part of the vents. Plus I wasn't sure on the original uncompressed seal thickness. Looks to be around 6-7mm thick when new, now that I had the new vents in hand.
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Vlad's rides thread

Post by vlad01 »

Car is up and running! Finally!

Before I took it out, I sorted this little bit that's always bugged me. The clutch fork covers sold by Rares is based on the V8 one, so even though it fits, it has a gaping hole with one corner missing when fitted to the V6.

I had plenty of 0.1mm 304 shim stock left over from another totally unrelated project. So I made this bit up using one of my spare covers as a template.

Then I stuck it on with some of that same aluminium foil tape.
IMG_1821.JPG
IMG_1822.JPG


Fits like a glove :thumbup: And that should keep the dust and crap out from contaminating stuff in the clutch and fork etc...


IMG_1829.JPG


I started the car, and as expected due to how it felt like, my Y pipe union on the driver side didn't seat right, I had an exhaust leak there. But over a few min it almost went by itself. I figured with the heating that the expansion and vibration was allowing it to settle into place where I couldn't get it to by hand.

I turned it off, let it cool a bit (still instantly burnt me, forgot that the HPC keeps the heat in like crazy), jacked it up a little and reaching in with the socket and spanner, yep it was a bit loose on both sides as expected due to settling in. I tightened it up, and zero leaks now, good as gold.


I then ran the car up the road and back, for a few Ks. Tested the cruise control virtual neural safety cut out, worked perfect! I love it when you spend a lot of time getting it right but in you're head you are only 80% confident it will work, and then it works! Fookin mint!

Got back, dumped the ATF and oil.

With much research I ended up going with Penrite 10 Tenths premium 10w60. Lots of details on why, but too much to write I think.


On the drive I found my wiper and washer to not work again. I had this a few times over the last few years and it came good each time. Well, I got to the bottom of the problem and it was a super easy fix.
Not sure how I didn't look into it to find such an obvious one.

IMG_1854.JPG
IMG_1855.JPG


The car drives great (apart from the shit handling since I have not done anything to the front end yet, other than the rack.)

I found the engine to vibrate a bit around that 1600 rpm like the balance shaft is missing, but seeing how the mirror looks on decel, it's obvious it's the mounts. They are a bit stiffer than any OEM one I have used, and I guess the mod to the driver side one only makes that worse. All other RPMs are good though and at it's worst, it still miles better than any solid/non OEM performance mount. I fully expect as it ages in, they will soften and settle a bit and it should improve.

The box whines a bit in 3rd on accel, nothing too crazy but noticeable. Slightly on the other gears too, same under load. I had Tony from Astro tell me that if its on accel and not decel, then the backlash is within spec and not too much. So likely just wearing in or a slight helix angle mismatch given there are like 3 brands of gears in there, with Tremec having dropped production on most of them. It seems to have quietened some already and I have only driven like 10ks so far, I am sure it will be fine. The shitbox actually whines on all except 4-5, both accel and decel and its gears, although used and mix/matched, were all in top shape. So that tells me it's nothing to stress about and it should dull off over time from the new box sharp whine to the well seasoned box whine, or no whine at all perhaps.

Importantly, I need to do lots of frequent fluid changes to keep wear particles contamination as low as possible for the next several K, to prolong the life of the box into the future


The shift quality is pretty good, but downshift quality and effort on all gears, even with large rpm gaps is absolutely unreal :punk:

The money, time and effort spent on the bellhousing and clutch work was well worth it. I can't even describe how easy it goes into gear when plowing down though the gears on a brisk decel. No manual car has even shifted down gears that effortless for me period.

I feel like the box could shift at infinite rpm lol. The effort didn't feel like it changes at all from almost no rpm delta to a large delta. Normally all manuals I have driven increase in effort as the rpm delta between gears increases. I felt none that I recall. It was really weird to experience, but this is a good weird haha.


Next on the list it to pick up the adjustable panhard from Pedders tomorrow for a reasonable price of 223 bucks. I was originally going to use Superpro there, but their bar was going up and up and up, now listed over 400 bucks in most places, I can't justify that sort of money for eventually a metal rod and a pair of bushes. I don't even need the adjustment, I just need one that is bent to clear the exhaust.

I am trying out Pedders bits and pieces for this build since I did have a good impression on their sports shocks for standard height in my red VP when I first bought it, felt very close to Bilstein, but they are all OEM in fitment, none of the stuffing around and compromises that Bilsein have.

I figured since Pedders stuff is certified, they should be safe with the panhard, a lot of the ones on the market are random no names and you just don't know with the weld quality, with the Pedders one, they have to back the product by law, same as Superpro. But the Pedders one looks like the same construction more or less for half the price, or should I say for a realistic price for what it is.

The guy at Centreline suspension in Thomastown highly recommended the Pedders OEM strut tops. He said that they are the only ones that have good rubber on them and they have two sets of stud holes, so you can adjust them somewhat by relocating the studs and mixing left to right in combo to get all sorts of adjustments.

So my plan is a full set of their standard height sports shocks, the top mounts and the panhard bar. Starting with the panhard tomorrow since that is all I can spare my cash on for now.

Their shocks are not cheap btw, pretty comparable to Bilstein at the time I bought them for the red VP.
You do not have the required permissions to view the files attached to this post.
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Vlad's rides thread

Post by vlad01 »

Not a lot to report on. Next lot of things need larger monies, so I'll have to save up for those.

Did sort the panhard bar out though. The Pedders one is quite good.

I copied the centers from the factory one, and then checked the tyre to guard clearances.

I loaded up the suspension with as many heavy object as I could find to try to get the car to half travel with, 5 brake rotors, a cylinder head, a flywheel, a clutch, full front VT conversion, a 4x4 battery, a bench vice, two sledge hammer heads. I was expecting much more compression, but I guess the factory springs are pretty strong then.


Not quite, but close enough I think. The pic is deceiving due to the shadow, but the rear was compressed a decent amount, enough anyway. The clearances at this height, nearly half way as mentioned, were identical on both measurements, or at least within 0.5mm. It's tricky finding a good spot as the guards do curve a little. But I used the exact same straight edge line on both wheels and double checked the front to back measurement point off one of the seam joints. It indeed was pretty bang on. Not sure what the point of having these adjustable when the correct measurement is the factory one. I suppose for those really low cars with short shocks, the half way to full travel will be closer to the bump stops, and I suppose it should be centered from that point. But I honestly think there should be a non adjustable bar with the bend to make it more affordable for those that just want the exhaust to fit and easier to install.


Either way, now I have ample exhaust clearance. I measured a difference of 30mm at the bend location over the factory one. My pipe was touching on full compression and has a witness mark. So I am confident there will be no issues whatsoever now.

Tightened the locking nuts, and added some paint on them to monitor them in case they come loose. The Superpro one did on the red VP on the first drive. So I wrenched them as tight as I could with a dab of loctite That one used bars with threaded internals and the adjuster was a double ended coupling bolt. The Pedders uses bars with tie rod like threaded ends, and the adjuster itself in a hollow threaded tube. So I understand that the Pedders one is build more like a link used in adjustable multilink suspension. Basically, opposite construction to the old Superpro one I have. I reckon there should be less side to side slop on the threads and thus less chance of coming undone like the Superpro one did. I have driven it a few times over the last 2 weeks and no probs so far. You could tell this one locked up a lot more positive than I recall for the Superpro one. I think the advantage comes from that each threaded connection is much farther apart, so less leverage on them as a pair.




IMG_1884.jpeg
IMG_1885.jpeg
IMG_1886.jpeg
IMG_1887.jpeg
IMG_1888.jpeg
IMG_1889.jpeg
You do not have the required permissions to view the files attached to this post.
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Vlad's rides thread

Post by vlad01 »

You may recall the coolant vs silicone seal tests I was conducting some months ago.

Well the results are in and... inconclusive.

Green 2-EHA left on all pics, purple free of that additive on the right of all pics.

As you can see there is no to little obvious difference or swelling. Original swelling actually went down rather quickly at the start, although my samples were sections that were least affected, there was some sections of swelling on both samples.

Evidence out in the auto industry says this happens at elevated temps and most prominent and fast acting approaching 100c or above. My tested were long term ones at room temp and doesn't mimic the engine environment.

This lack of temp also explains why my computer's previous water cooling system was not affected by inadvertently using 2-EHA laced coolants for almost 2 decades before I retired that system to a retro PC collector this year. That cooling system used silicone everywhere, lots of plastics too. The hoses were pure silicone, none of it was affected at all, but the max temp was probably 60c with most of the time it sitting in the high 30s to mid 40s. Probably does not happen at low/lower temps and it appears to be somewhat reversible once the surrounding concentration of 2-EHA goes down or away, except where the seals have physically already ruptured.


I don't have a means of testing at operating temps other than doing it in the car and testing over multiple years. I will change my intake gaskets and switch to the purple anyway on the white car before it is ready to be a daily, and check it say 3-5 years down the track.


IMG_1915.jpeg
IMG_1916.jpeg
IMG_1917.jpeg
IMG_1918.jpeg
IMG_1919.jpeg
IMG_1920.jpeg
You do not have the required permissions to view the files attached to this post.
OND150
Posts: 18
Joined: Wed Oct 21, 2026 9:12 am
cars: Vr v6 wagon

Re: Vlad's rides thread

Post by OND150 »

Sweet ride bud, that reminds me I really need to sort out a adjustable panhard great stuff
:turbo: :comp: :typist:
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Vlad's rides thread

Post by vlad01 »

Cheers!

I give the Pedders one a thumbs up of approval, well priced and backed up with quality assurance. I'd be wary of the cheap ones on ebay. Welds and multi piece design inherent to these are one of those things that you want to make sure quality is up to safe standards.

Superpro is my go to for the majority of suspension parts and bushes, but their panrard is just way too expensive for what it is. Well over 400 bucks now. I think the current ones they sell follow the same design with the adjuster as this one does, but the superpro one on the other car was bought in 2017 and used the other adjuster design.
OND150
Posts: 18
Joined: Wed Oct 21, 2026 9:12 am
cars: Vr v6 wagon

Re: Vlad's rides thread

Post by OND150 »

Definitely not your first rodeo judging by the 361 pages lol
:turbo: :comp: :typist:
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Vlad's rides thread

Post by vlad01 »

Definitely not haha, and my tinkering with cars and stuff goes back a lot further than this forum. Since 13 back in the early 00s with padock bombs and what not.
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Vlad's rides thread

Post by vlad01 »

I forgot to mention with regards to the engine mount vibration thing. It appears to be a property of the rubber vs temp. As some heat gets into them, the problem goes away entirely. Rocking the engine by hand shows quite a difference from cold to after being driven for 20 min. Much softer after a drive, with it hardening back up some hours later. Hopefully the rubber goes though an aging process and softens up a little, if not, I'll get the $$$ Kelpro ones which I speculate will be the best on the market given my experience with everything Kelpro being excellent, but you do pay for it. About 120-150 each they cost. My GTE1H ones were like 30 odd each :lol:
Charlescrown
Posts: 2097
Joined: Fri Aug 05, 2011 9:58 pm
cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes
Location: Padstow NSW

Re: Vlad's rides thread

Post by Charlescrown »

From memory those cars has fluid filled engine mounts and the common complaint when workshops fitted after market mounts was the vibration but hey it's the nature of the beast.