No, an E38 cannot become E67 because a lot of hardware is physically not present on the E38.
Curiously enough-there are TWO H-bridge drivers with potentiometer based feedback on the E67, one is used on the V6/V8/I6 systems for throttle control, and the other one is used on I4 systems for throttle control. I can't tell if I can use both of them on the same OS or not, but the LSA has a complete second code path to run the dormant H-bridge system.
E67/T42 Mapping and Modding
-
Xnke
- Posts: 107
- Joined: Thu Sep 24, 2015 3:42 am
-
Rapidfire
- Posts: 66
- Joined: Sun Oct 18, 2026 9:56 am
- cars: Vp Group A Rep
Ve 6.0 Lsa 6 speed Ute
Vf Redline Wagon
L300 Van with 3.8 Buick
Re: E67/T42 Mapping and Modding
Yea i know what you mean, but could you plug e67 into e38 loom ? sorry should be checking my self. I'm guessing I'd have to repin my E38 connector to work with the E67. and then is the os compatibility with the dash. which you will be able to do a hybrid E 67 to E38 OSXnke wrote: Mon Nov 16, 2026 4:20 am No, an E38 cannot become E67 because a lot of hardware is physically not present on the E38.
Curiously enough-there are TWO H-bridge drivers with potentiometer based feedback on the E67, one is used on the V6/V8/I6 systems for throttle control, and the other one is used on I4 systems for throttle control. I can't tell if I can use both of them on the same OS or not, but the LSA has a complete second code path to run the dormant H-bridge system.
-
antus
- Site Admin
- Posts: 10111
- Joined: Sat Feb 28, 2009 10:34 am
- cars: TX Gemini 2L Twincam 8psi
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Subaru WRX 2007
Re: E67/T42 Mapping and Modding
no, e38 is 2 connector and doesnt have the e67 blue connector and the e67 has 3, fully different electrically.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
Rapidfire
- Posts: 66
- Joined: Sun Oct 18, 2026 9:56 am
- cars: Vp Group A Rep
Ve 6.0 Lsa 6 speed Ute
Vf Redline Wagon
L300 Van with 3.8 Buick
Re: E67/T42 Mapping and Modding
my thought was in my 2011 VE SSV ute the power coupler going into the E38 change the pin out E67 then I could utilize the other two plugs, I've just disconnected the electronics for the boost control on the Lsa, the only other issue is E67 won't communicate with the 2011 dash I've tried it with different Os. E67 would be good for boost and wastegate for the turbo.antus wrote: Mon Nov 16, 2026 8:03 am no, e38 is 2 connector and doesnt have the e67 blue connector and the e67 has 3, fully different electrically.
making the E67 OS communicate with any other vehicle would be a milestone. or rusefi real time for e38
https://github.com/rusefi/rusefi/wiki/GM-E38
-
antus
- Site Admin
- Posts: 10111
- Joined: Sat Feb 28, 2009 10:34 am
- cars: TX Gemini 2L Twincam 8psi
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Subaru WRX 2007
Re: E67/T42 Mapping and Modding
Oh yeah, I literally meant you cant plug it in, re-wire it might be possible.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
Xnke
- Posts: 107
- Joined: Thu Sep 24, 2015 3:42 am
Re: E67/T42 Mapping and Modding
It's possible, but you might be better off building a new harness.
I'm working with the 2005-2006 VPW-CAN transition years right now, so getting the E67 to talk to my VPW-based car is something I am pretty sure I've got working-I'm waiting on plugs and connectors to hook up the new bench harness with the BCM and IPC.
Getting the E67 to speak the proper dialect of GMLAN Canbus shouldn't be that hard, especially if you have enough info about which modules are the gateway modules for that platform.
I'm working with the 2005-2006 VPW-CAN transition years right now, so getting the E67 to talk to my VPW-based car is something I am pretty sure I've got working-I'm waiting on plugs and connectors to hook up the new bench harness with the BCM and IPC.
Getting the E67 to speak the proper dialect of GMLAN Canbus shouldn't be that hard, especially if you have enough info about which modules are the gateway modules for that platform.
-
Xnke
- Posts: 107
- Joined: Thu Sep 24, 2015 3:42 am
Re: E67/T42 Mapping and Modding
Alright, I've gotten into the weeds here. I don't know enough about tuning the Gen4 style PCMs to work out the tables and values.
Anyone here want to have a look at what I've got going on, and tell me just how far wrong I've got it?
Intention is to give BinTool some limited tuning abilities, basically a high/low spark table, ability to extend tables for boosted operation, etc. Not a full-tilt tuning tool but enough to get a car started and running, and get it dialed in for daily operation.
Basically, enough to get my truck swapped and ready to drive to work...
Right now I have high confidence in the Baro sensor and 1/2/3 bar MAP sensor modifications, but it's time to rescale the fueling tables and that's what I need to be sure I'm doing correctly. Once I get the fueling tables extended, next up is setting the breakpoints for the torque model, because they'll need to move around I'm sure.
Anyone here want to have a look at what I've got going on, and tell me just how far wrong I've got it?
Intention is to give BinTool some limited tuning abilities, basically a high/low spark table, ability to extend tables for boosted operation, etc. Not a full-tilt tuning tool but enough to get a car started and running, and get it dialed in for daily operation.
Basically, enough to get my truck swapped and ready to drive to work...
Right now I have high confidence in the Baro sensor and 1/2/3 bar MAP sensor modifications, but it's time to rescale the fueling tables and that's what I need to be sure I'm doing correctly. Once I get the fueling tables extended, next up is setting the breakpoints for the torque model, because they'll need to move around I'm sure.
-
MPC001
- Posts: 188
- Joined: Sat May 05, 2018 11:41 am
Re: E67/T42 Mapping and Modding
You could check out your bin edits in EFI live.
-
Xnke
- Posts: 107
- Joined: Thu Sep 24, 2015 3:42 am
Re: E67/T42 Mapping and Modding
Alright, so I had a member here share a very complete XDF for the Malibu LZ9 binary, and lo and behold, all the factory forced induction code is there. All that work and time spent, and I really didn't have to do it!
Now I'm focusing on tracing it out and nailing down the routines that need to be turned on/turned off, updating the selectable sensor types, and making sure that the appropriate CAN and J1850 messages can be turned on/off to drop this into any 6 cylinder application.
It *looks* like I can get the COP and coil-pack style ignition system to be selectable, but I haven't worked through all that yet. It's on the list.
I should have an updated BinTool version by this weekend, that is ready to post up for a test.
Now I'm focusing on tracing it out and nailing down the routines that need to be turned on/turned off, updating the selectable sensor types, and making sure that the appropriate CAN and J1850 messages can be turned on/off to drop this into any 6 cylinder application.
It *looks* like I can get the COP and coil-pack style ignition system to be selectable, but I haven't worked through all that yet. It's on the list.
I should have an updated BinTool version by this weekend, that is ready to post up for a test.
-
MPC001
- Posts: 188
- Joined: Sat May 05, 2018 11:41 am