Converting 202 to ABS Crank Trigger

[VL400]

There is info on converting to DIS using a delco here .. https://pcmhacking.net/forums/viewtopic.php?f=15&t=128


This picture shows the difference in slot/tooth width and what it does to the signal (on an extreme level). The amplitude difference is just that the simulation wheel runout was really bad

Narrow vs wide slot.jpg (35.27 KiB) Viewed 7462 times

Wide slot SM.jpg (116.25 KiB) Viewed 7462 times

Sensor width slot SM.jpg (124.31 KiB) Viewed 7462 times

[VX L67 Getrag]

WOW.. even for a novice like me... that is friggen amazing!!!!

HOLDEN202T have you got your back in action & put it to the test yet & not on a torsional balancer?

[Holden202T]

no i haven't, i've just recently put the abs sensor back on the motor with the diodes in place but other than some testing in the shed i haven't used it at all

[Holden202T]

ok nice update today

got one of VL400's ignition modules to run on the gemini, this is going to be the way to make 6 coils happen (with the right crank trigger) on the 202, and so the first step was to get it wired into the delco to replace the camira ignition module etc.
so far so good, its running on the 202 dizzy pickup and ignition module firing 1 x LS2 coil and is working flawlessly (in the shed atleast).

so now will work on getting the abs sensor on the balancer working then it will be another step closer!

heres a video of the car running and showing the wiring and ls2 coil aswell as the module inside the car.
[youtube]http://www.youtube.com/watch?v=QagRavs1J4g[/youtube]

and i had to test the rev limiter function 3000rpm setting.
[youtube]http://www.youtube.com/watch?v=7D3JJKemz-c[/youtube]

hoping to tidy this up now, ie. rather than running the wires out to the delco wires in the bay (that used to connect to the camira module) i'll run them and power all internally in the car to the ecm then just need the trigger wires and coil driver wires going out into the bay, should clean it up a bit then.

[delcowizzid]

i cant wait for one of these so i can use a launch limiter to spool the turbo on the vb crazy

[Holden202T]

got the abs sensor working with this last night too.

got a log of the two one after the other to show the difference, even at low revs where the dizzy trace is alot smoother its still nowhere near the smoothness of the abs sensor!

dizzy trace.jpg (118.24 KiB) Viewed 7360 times

abs sensor trace.jpg (140.23 KiB) Viewed 7360 times

now this is working i am thinking of cutting 5 teeth of the dizzy rotor and using it as a sync reference for cam sensor and then i can try some more coils

[antus]

What an improvement! Thats really working out well

[delcowizzid]

if you need even more spark LS2 truck coils have 3 times the amperage of an ls1 coil and are a lot cheaper

[Holden202T]

i'm using LS2 coils (i have 8 of them ) but i don't think they are off a truck. either way its going to shit all over the camira coil i was running before so im sure it will be fine

[VL400]

There are a number of different LS2 coils, some even have a small heatsink on the rear. The ones holden202 have are D513A. I have compared a D514A to a LS1 coil and it makes the LS1 spark look (and sound) comparatively small - current draw is FAR higher on the LS2 coils, but dwell times are also shorter to reach saturation.