My Delcoed Rides

[Holden202T]

yeah i plan to get some of that spray stuff, not so much to pretty it up but to fully seal it up from weather etc

i did paint that rust converter stuff on before the cold gal .... never really been 100% sure if it really does anything

[Dec_head]

I have painted on the rust converter primer in one where it was rusty and i had ground it back on a 4x4 i had.
Then left it on untouched for over 12 months and drove around and left it out in the weather and it never rusted again.
That other crap that you paint on then wash off i don't know that it works sort of defeats the purpose i won't use it.

[Holden202T]

sounds like you've thoroughly tested it then

[simc]

Great stuff, Love the diff setup in the Gemi, should get off the line real well.

[Holden202T]

i sure hope so

[Holden202T]

well i've been hard at it with the panel work ....

as you know i blanked off the fuel filler on the rear pillar so i thought i'd finish the other side of that job.

P1070237.jpg (177.93 KiB) Viewed 6621 times

if you want to see what this looked like before, go back a page and theres a pic of the parcel tray.

i've mostly completed the making of this panel to seal off the boot - was alot of in/out fit, cut, fit, cut but it fits sweet now!

P1070315.jpg (158.08 KiB) Viewed 6621 times

P1070316.jpg (141.6 KiB) Viewed 6621 times

next step will be to weld it all in.

[Holden202T]

well i've manged to finish all the rust repairs on the back window, but nothing much to see ... but i have also finally found some bits i've been in need of for ages.

bumpers and grille!!

P1070325.jpg (180.21 KiB) Viewed 6621 times

i did actually want TF/TG bumpers because they are plastic and lighter than the steel ones, but i just can't find any at wreckers etc so i had to settle for TE ones.

Its really strange looking at the car now like this as i've had it for nearly 2 yrs and never had them

so most of the work i need to do to run it down the strip is nearly done, i have to finish some primer/paint when the sun comes out and im going to ring the local andra tech inspector this week and see when he can fit me in for a check over and then hopefully i'll know weather i need to do more stuff or if its ready to race!

now to save for some pretty mags!

[Dec_head]

If your looking for mags i rememeber years ago i had a 4 cylinder bmw like 1976-1982 were the same stud pattern as a gemini i picked up those two piece neals wheels for stuf all

[Holden202T]

i know what wheels i want, they just cost lots

i figured i'd start with the fronts, some nice 15 x 4 inch wide ones and then worry about the rear afterwards .... im also yet to find out how much traction i'll have aswell as weather i need a taller tyre or not so for that rear i'm going to start with the rears that are on it now.

[Holden202T]

sold my old motorbike last weekend, pretty much never ride it cause its broken and don't want to commit funds to it so i thought, sell it off and use the dollars for the gemini and i did

P1070474.jpg (158.01 KiB) Viewed 6621 times

P1070475.jpg (139.89 KiB) Viewed 6621 times

did a bit of a trial fitting .... mainly wanted to make sure they cleared the VT calipers and they do as they sit out a fair bit, should be just inside the guards with tyres on it!

also got the tailshaft loop ... had a quick look under the car and i reckon the tunnel is going to need some persuasian but shouldn't be too bad, so hopefully fit that in the coming week ... need to get my jack back from my brother!!! slack ass borrowed it a few weeks ago and was going to bring it straight back!!!