Tuner Pro RT L67 VE Tables

Holden/Delco Tuning. ALDL, OBD 1.5. Circa 1989 to 2004.
User avatar
antus
Site Admin
Posts: 10111
Joined: Sat Feb 28, 2009 10:34 am
cars: TX Gemini 2L Twincam 8psi
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Subaru WRX 2007

Re: Tuner Pro RT L67 VE Tables

Post by antus »

Also note that dead time changes depending on the chips driving the injectors, so you can get in the ball park with manufacturer specs, but they won't be fully correct for this PCM. So you may need to change it a little from manufactures data, which is difficult to get right. I spoke to an AI about it and it had some ideas for me how to test and change and measure and correct, but I had been lucky enough with the educated guesswork numbers on my car and the injectors were already working quite well so I didn't follow through. But if all indicators are your dead times are wrong, you may want to see what you can come up with to try and dial them in better from manufacturers specs. The only time this wont be true is if the manufacturer says they are the specs for that specific pcm. It's not necessarily your problem but something to keep in mind.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
LoneOranger
Posts: 7
Joined: Sat Jan 24, 2026 4:26 am
cars: VR utility
RC Colorado
FJ45 utility

Re: Tuner Pro RT L67 VE Tables

Post by LoneOranger »

This engine is running an earlier 808 ECU if that helps and it’s T5 manual. I have a lot to learn and lots of research ahead of me. I will have to look in to how I go about wiring in the WB to the ECU. I was just going to use it separately which probably isn’t ideal. But it would at least give me an idea what was going on and I could tweak things accordingly.

I greatly appreciate all your input too guys.
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Tuner Pro RT L67 VE Tables

Post by vlad01 »

If it has a analog 0-5V output, wire that to I think D8 on the ECU and make sure the WB ground is good and shares one on the ECU side somewhere to ensure a cleaner signal.

In the tune, there is a 0v and a 5v WB input AFR setting. You can adjust those to the specs of your WB and it's controller and fine tune it from the sequencer assuming it has one.

My one for eg. is AFR 10 when 0v and 20 AFR when at 5v. Of course there is some slight error between the sensor and the ECU's signal processing. So mine was more like 10.2 and 19.8 or something like that to get the calibration sequence to report a perfect 10, 13.3,16.6 and 20 when powered up, indicating the calibration is spot on.

Mine is an old 14Point7 kit from like 10-15 years ago, and there have been many alternatives since then, but most follow a similar spec still.


The FAQ on the green "?" on the top right has all the documentation for all the setup and hardware and basic tuning info. WB is well covered in those documents.
User avatar
antus
Site Admin
Posts: 10111
Joined: Sat Feb 28, 2009 10:34 am
cars: TX Gemini 2L Twincam 8psi
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Subaru WRX 2007

Re: Tuner Pro RT L67 VE Tables

Post by antus »

Sometimes there is signal and power ground. If your power (for the heater) has separate connections wire the signal close to the pcm, and the power to some fat power wires further away from it. The reason is the heat circuits usually switch heavyer power quickly which creates electrical noise. Fat power cables mat it less susceptible to interference and the distance from the PCM allows there to be some capacitance in the cable which also helps flatten the sharp power switching. If you wire all of the power together and near to the PCM, that is when you can have interference problems between the WB heater circuit and the analog signal.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396