Tuner Pro RT L67 VE Tables

Holden/Delco Tuning. ALDL, OBD 1.5. Circa 1989 to 2004.
LoneOranger
Posts: 7
Joined: Sat Jan 24, 2026 4:26 am
cars: VR utility
RC Colorado
FJ45 utility

Tuner Pro RT L67 VE Tables

Post by LoneOranger »

G’day there,

Just chasing some advice on what people’s VE tables are looking like on Tuner Pro RT for their L67’s? Looking to compare mine with more modified L67 engines as mine isn’t stock and whether you are smoothing them out for best engine operation? My 3D table looks quite erratic, so curious as to what your thoughts are. Thanks.
You do not have the required permissions to view the files attached to this post.
User avatar
Rapidfire
Posts: 66
Joined: Sun Oct 18, 2026 9:56 am
cars: Vp Group A Rep
Ve 6.0 Lsa 6 speed Ute
Vf Redline Wagon
L300 Van with 3.8 Buick

Re: Tuner Pro RT L67 VE Tables

Post by Rapidfire »

Could be from wrong injectors ? or injector data

Think we need more info than VE table

Stock ? Camed ? any mods, Bigger supercharger pulley

Hope this helps,
You do not have the required permissions to view the files attached to this post.
LoneOranger
Posts: 7
Joined: Sat Jan 24, 2026 4:26 am
cars: VR utility
RC Colorado
FJ45 utility

Re: Tuner Pro RT L67 VE Tables

Post by LoneOranger »

Thanks, Rapidfire. It’s good to be able to look at some tables for an L67 for comparison.

It’s running Siemens 60lb injectors, ported M90 SC and LIM, 71mm pulley (makes 12.4psi), mildly ported heads, W2A intercooler, 85mm LS throttle body, Comp Cam and extractors flowing into 2.5” system and then into 3” cat back system. Tuned and runs on 98.

I was just curious if that was normal as it looks pretty rough to me. I would expect it to look more linear like your tables. Makes good power but I want to get it running as well as it can run.

I’m trying to learn how to use Tuner Pro RT and when you look at the parameter tables, there are so many things to get your head around. I’m assuming that most of them aren’t something that people are adjusting. So I’m keen to learn what I should be focussing on. I’m using the OSE_12P V112 XDF for 1,2 and 3 Bar Petrol.
User avatar
Rapidfire
Posts: 66
Joined: Sun Oct 18, 2026 9:56 am
cars: Vp Group A Rep
Ve 6.0 Lsa 6 speed Ute
Vf Redline Wagon
L300 Van with 3.8 Buick

Re: Tuner Pro RT L67 VE Tables

Post by Rapidfire »

Ok, good info.

What im seeing is wrong injector flow & dead time.

If you using std flow tables, thats what can cause unevenness of Guessing flow tables to bigger injectors

generally when you buy from reputable company they will give you flow rate and dead time

Then using wideband to correct ve table, big dips and risers.

Can you confirm injector flow is correct ?
LoneOranger
Posts: 7
Joined: Sat Jan 24, 2026 4:26 am
cars: VR utility
RC Colorado
FJ45 utility

Re: Tuner Pro RT L67 VE Tables

Post by LoneOranger »

I have added my injector bias vs battery voltage and bias offset vs BPW tables. When you say flow rate are you talking actual physical flow rate on a flow bench or the fuel table settings? I have thought about getting the injectors flow tested just to ensure they are evenly matched. I bought new Siemens Deka through TI Performance as there was a two month wait to get my originals tested and serviced at the place I wanted to use here in SA. I didn’t pay attention as to whether there was an information sheet with them at the time and wasn’t something I was going to be doing myself anyway. I bought the car with issues but fixed those and then had it retuned. It ended up being a corrupted memcal. Naturally as the project has progressed, I have gained an interest in learning all aspects of the vehicle including tuning. This is the injector data that I’m probably going to use as a base line. Just to see what effect it has.
You do not have the required permissions to view the files attached to this post.
LoneOranger
Posts: 7
Joined: Sat Jan 24, 2026 4:26 am
cars: VR utility
RC Colorado
FJ45 utility

Re: Tuner Pro RT L67 VE Tables

Post by LoneOranger »

Here are my other tables to match the ones you sent earlier.
You do not have the required permissions to view the files attached to this post.
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Tuner Pro RT L67 VE Tables

Post by vlad01 »

Some general tuning advice. Smoothing is a pitfall many people fall for. You want the VE to be representative and thus be as accurate to what's actually happening in your engine. So if it's spiky, it's spiky. Most engines have some spikes, and the more modified the more they get them. Large cams with lots of overlap have often huge waves in the table with high frequency ones more towards idle and light loads.


So by smoothing them out, you make the tune way less accurate, eg. where the engine hit a constructive harmonic and wanted more air and fuel, there is a spike, but smoothing has removed that. The result is that area now runs lean, so in the WB data it shows up as a lean spike, and the inverse for troughs where the engine hits destructive interference in the exhaust/intake/cam dynamics.

What you want is the target AFR and WB to follow tightly during steady state in all cells where practical. If that's all good, then your VE is true and representative assuming all other modifiers are right.


That all said, where false spikes can occur, is when there is a data log to actual event delay and that logs one or so cells out from the real one in a feedback loop. This delay comes from the engine and WB itself, the WB response time, and of course the speed of the intake and exhaust gases traveling from the injection event all the way to the WB sensor, then out the 0-5v wire. So this is why steady state during tuning is important and why transients in the logs during VE calc should be tossed out of the data. The type of history stat is equality important, looking at running and history average, min and maxes, and amount of hits all tell you the validity of that data and human discretion plays a vital role here. You need some understanding in stats though to be able to know which data is iffy and what is good stuff.

I have not had this delay induced false cell thing happen to me in the 15 years of tuning, but I have seen it on one race engine where the idle cells in the main table went into a feedback loop. The calc VE made one cell higher and higher and one lower and lower. This was due to an idle hunt coupled with the delay that had the lower cell's data land on the upper one and vice versa because the engine was hunting between the two, but the lag was trailing the data behind at exactly the right rate to land the opposite cells. This made the hunt worse and worse and the spike and trough kept on growing. It was obvious by the end with the way the idle tanked and the mirror twin spikes that were massive appeared from seemingly nowhere. This was manually tuned out, and nothing smooth would have fixed anyway. But I added this for some context, because it technically falls into a transient event when at first glance it would seem steady state, another pitfall that looks related on the surface to the whole smoothing thing.
LoneOranger
Posts: 7
Joined: Sat Jan 24, 2026 4:26 am
cars: VR utility
RC Colorado
FJ45 utility

Re: Tuner Pro RT L67 VE Tables

Post by LoneOranger »

I appreciate that vlad01. As you say it’s all about experience and I have zero with tuning fuel injection lol. It’s like reading Japanese sometimes and I’m always impressed at the knowledge the people on this site have when it comes to understanding ECU programming. What I am good at is listening to the motor and now I’m trying learn how that translates into what I’m seeing on TP RT. I’m reluctant to make changes as I can’t afford to damage the engine but I am keen to fine tune it and learn.

My key take from what you just said is learning what looks normal and what looks abnormal. This is where I get a bit lost having never hooked a laptop up to a vehicle and be able to data log it in operation. But I do love the fact I can now data log out on the road and then replay it. My only gripe is that I wish the data log also recorded sound lol.

I have purchased a WB analyser but yet to use it but that is the next step to see what is actually going on in real time. My L67 is in a VR ute so it’s only running the single O2 sensor on passenger side. So I don’t know what the drivers side bank is doing currently. But I’m going to place the WB either in the drivers side exhaust or after the Y-pipe to read both banks.

I will add the last data log I performed also just to give you some idea what is going on. You might see something I'm not seeing. I have changed the O2 sensor as it appeared to be sticking or lazy. Now idles and runs smoother.
You do not have the required permissions to view the files attached to this post.
User avatar
vlad01
Posts: 8600
Joined: Mon Oct 08, 2012 8:41 am
cars: VP I S
VP I executive
VP II executive
VP II executive #2
Location: Kyneton, Vic

Re: Tuner Pro RT L67 VE Tables

Post by vlad01 »

The WB will be critical for proper tuning. Using the standard O2 is possible and very accurate when used in a cleaver way, that is using the short term and long term fuel trims that are part of closed loop fueling and then adjusting each point in the VE table until that cell gives a zero fuel trim when holding the engine at that cell for long enough. However, this relies on the target AFR being 14.7, fuel trim only works at that exact AFR. If you have ever looked at an o2 voltage curve, you'll know that going by voltage alone is pretty futile. The curves just either side of stoich shoot off almost vertical, if you haven't see it, google it and you'll know exactly what I am talking about. Closed loop fueling uses the cross point of that curve rather than exact voltages to determine when it's at 14.7, that cross point happens to be at around 450mV often mentioned in tuning.


I'd get that WB installed, wired up to the PCM and calibrate it, most have a calibration output sequence on stat up that allows you to adjust the 0-5v in the tune until the readings match the specified sequence output steps. Eg, AFR sequence of 10, 13.33, 16.66, 20.
User avatar
Rapidfire
Posts: 66
Joined: Sun Oct 18, 2026 9:56 am
cars: Vp Group A Rep
Ve 6.0 Lsa 6 speed Ute
Vf Redline Wagon
L300 Van with 3.8 Buick

Re: Tuner Pro RT L67 VE Tables

Post by Rapidfire »

I agree with vlad`s smooth isn`t always correct,

I`d check the injectors. Building any engine start`s with right flow balanced injectors, with right Calibration data.

And right fuel pressure. Dont just assume everything is correct before chasing the VE table.

The earlier tuner might’ve compensated for something using wideband, but that’s not confirmed.

Just things i start with before i go tuning.

If you posted your bin file we could help check before you start