Page 13 of 57
Re: OSE 12P V105
Posted: Thu Jun 10, 2010 2:01 pm
by VL400
Have released V105, it has the following changes...
Code: Select all
; Code Changes
; Made C15 Normal Logic
; Read Spare Dig Input Pins C9 and D11
; Bug Fixes
; 8800RPM Boosted VE Table Missing
; XDF Fixes
; ERR # 45 Params - Renamed 45, were still 44
; 11..2 volts in IAC - Desired RPM
; Closed Loop enable temp formatting
; Single/Double Fire - made it more english
; Cal Changes
; BLCD Boosted Coolant advance is -20
; Created A APNX cal for series 1 V6 - it will need work so if any users would like to contribute please do
; ALDL Changes
; Removed PROM ID (16bit)
; Removed Scaled MAP LV
; Added Input Status Flags For C8, C9 (active with 12V), C15 and D11
; Added Input Status Flag for Map Switch
; Added Transient Fuel (16bit)
; Changed Desired Idle RPM To One That Changes At Idle Instead Of > 5kph
; Added DE
You must use the included ADX files as the data stream has changed. The APNX cal is intended as a starting point, if you want to help improve it please do. The input status flags are all active when grounded except for C9 which is active on 12V.
The flashtool V1.21 (and later) has support for OSE 12P V105
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 4:50 pm
by VL400
And second update for today, V110. Changes to the ALDL 128byte write in readiness for the TP5 plugin otherwise its the same as V105. Flashtool V123 (or later) supports this version.
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 5:15 pm
by antus
Awesome work, nicely done.
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 8:19 pm
by jacomms
To Nice.......as always
Justin
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 8:46 pm
by Holden202T
dead set, you can read the delco matrix!!
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 8:48 pm
by vn5000
Nice work VL400
I think there may be a problem when migrating a v104 cal to a v110 cal .
I wrote the v110 bin onto nvram and when i went to write the cal i migrated to v110 ,the flash tool started writing the cal but then stopped after a few seconds.Know it wont connect to ecm at all ,the nvram must be corrupted .
I noticed when i migrated the cal the progress bar didnt go to the end but it did when i migrated it to a v105 cal.
Anyway ill put the nvram in the burner and try writing a v105 migrated cal.
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 8:51 pm
by Holden202T
if you haven't done so already, might be worth reading the whole chip off the nvram and posting it to VL400, if something has stuffed up he might be able to get some leads one whats happened with it from the corrupted file.
i'll try and get my v1.04 updated tonight and see how it goes.
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 9:22 pm
by Holden202T
ok well i updated the ecm to v1.10, no problems, also migrated the cal v1.04 -> v1.10 no issues, loaded into the ecm and started the car, runs fine, logging works fine also....
only issue i did have it using the flex table editor on v1.10 doesn't work, says theres no flex info .... yet the table in the xdf shows all the numbers in it just no axis info .....
v1.04 cal that i used to migrate shows up fine in the flex editor.
have scanner pro logs/bins/cals/flash tool logs etc if anyone wants to compare or anything.
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 10:04 pm
by vn5000
Sweet ,just got it all sorted myself ,just a bad solder joint on my diy nvsram adapter .
Im not using flex tables at the moment so i havent had that problem.
Re: OSE 12P V110
Posted: Thu Jun 10, 2010 11:16 pm
by VL400
Holden202 wrote:only issue i did have it using the flex table editor on v1.10 doesn't work, says theres no flex info .... yet the table in the xdf shows all the numbers in it just no axis info .....
v1.04 cal that i used to migrate shows up fine in the flex editor.
Oops, that'll teach me for rushing it! Will fix it now.
EDIT: Try version 1.23 of the flashtool.