Page 52 of 56

Re: PCM Hammer P12 development

Posted: Wed Sep 21, 2022 1:32 pm
by antus
This is the OS segment you need, I dont have a complete file but if you make it line up you should find the flipped bit.

Re: PCM Hammer P12 development

Posted: Wed Sep 21, 2022 2:38 pm
by Sleepy
antus wrote:This is the OS segment you need, I dont have a complete file but if you make it line up you should find the flipped bit.
Strange the first 0x18000 Bytes do match then after that my file has what apparently is the speedometer cal.
12597778_Compare.PNG
12597778_Compare.PNG (39.75 KiB) Viewed 3040 times
12597778.PNG
12597778.PNG (24.76 KiB) Viewed 3040 times

Re: PCM Hammer P12 development

Posted: Wed Sep 21, 2022 2:54 pm
by antus
can you post yours up?

Re: PCM Hammer P12 development

Posted: Wed Sep 21, 2022 3:15 pm
by Sleepy
antus wrote:can you post yours up?
Here it is.
12597778_corupt.bin
(1 MiB) Downloaded 97 times

Re: PCM Hammer P12 development

Posted: Wed Sep 21, 2022 3:58 pm
by antus
It looks like the OS segment is split, part at the start of the file, part after the calibration segments etc. Apply a 163840 byte offset (decimal) to verify the second part. This aligns the SPS bin with the end of your file and the data then matches from the point you have highlighted to the end. Your bit flip is at 45D9F in your file which is F9 in the corrupt file and its F8 in the factory file.

Re: PCM Hammer P12 development

Posted: Fri Sep 23, 2022 11:42 am
by Sleepy
Thank you so much. I have some questions about reversing the OS now, but I will find a better thread.

Re: PCM Hammer P12 development

Posted: Sat Dec 31, 2022 9:04 am
by bill12690
I'd like to share the bin from my 04 Ion Redline donor PCM. This was an LSJ/5 speed P12 car. I wish I knew more about the XDF development process, I'd be down to help. I've also cross-posted this in the PCM Hammer 021 release thread as well.

[06:32 22:011] PCM Hammer 021
[06:32:22:013] Friday, December 23 2022 @06:32:22:01
[06:32:22:466] Device Found: OBDX Pro GT
[06:32:22:499] Device Successfully Initialized and Ready
[06:32:24:669] VIN query failed: Timeout
[06:32:26.632] VIN query failed: Timeout
[06:32:29:650] VIN query failed: Timeout
[06:33:01:4211 VIN: 1G8AY12P34Z207779
[06:33:01:459] OS ID: 12597978
[06:33:01:468] Hardware Type: P12
[06:33:01:519] Calibration ID: 0
[06:33:01:6371 Serial Number: 4131KE005
[06:33:01:681] Broad Cast Code: YKHW
[06:33:01:717] MEC: 0
[06:33:15:899] Will save to C:\Users\k_blo\Downloads\Pcm Hammer021\LSJ.bin
[06:33:25:897] Querying operating system of current PCM.
[06:33:25 934] OSID: 12597978
[06:33:26:039] Unlock succeeded.
[06:33:26:055] Attempting switch to VPW 4x
[06:33:26:097] Module Ox10 (engine controller) has agreed to enter high-speed mode
[06:33:28:027] Kernel upload 49% complete.
[06:33:28:826] Kernel upload 100% complete.
[06:33:29:453) Kernel Version: 0103050C
[06:33:29:460] kemel uploaded to PCM succesfully. Requesting data...
[06:33:29:474] Flash chip: AMD AM29BL802C, 1mb

Re: PCM Hammer P12 development

Posted: Mon Jan 16, 2023 6:35 am
by spyder09
bill12690 wrote:I'd like to share the bin from my 04 Ion Redline donor PCM. This was an LSJ/5 speed P12 car. I wish I knew more about the XDF development process, I'd be down to help. I've also cross-posted this in the PCM Hammer 021 release thread as well.

[06:32 22:011] PCM Hammer 021
[06:32:22:013] Friday, December 23 2022 @06:32:22:01
[06:32:22:466] Device Found: OBDX Pro GT
[06:32:22:499] Device Successfully Initialized and Ready
[06:32:24:669] VIN query failed: Timeout
[06:32:26.632] VIN query failed: Timeout
[06:32:29:650] VIN query failed: Timeout
[06:33:01:4211 VIN: 1G8AY12P34Z207779
[06:33:01:459] OS ID: 12597978
[06:33:01:468] Hardware Type: P12
[06:33:01:519] Calibration ID: 0
[06:33:01:6371 Serial Number: 4131KE005
[06:33:01:681] Broad Cast Code: YKHW
[06:33:01:717] MEC: 0
[06:33:15:899] Will save to C:\Users\k_blo\Downloads\Pcm Hammer021\LSJ.bin
[06:33:25:897] Querying operating system of current PCM.
[06:33:25 934] OSID: 12597978
[06:33:26:039] Unlock succeeded.
[06:33:26:055] Attempting switch to VPW 4x
[06:33:26:097] Module Ox10 (engine controller) has agreed to enter high-speed mode
[06:33:28:027] Kernel upload 49% complete.
[06:33:28:826] Kernel upload 100% complete.
[06:33:29:453) Kernel Version: 0103050C
[06:33:29:460] kemel uploaded to PCM succesfully. Requesting data...
[06:33:29:474] Flash chip: AMD AM29BL802C, 1mb

12597978 is an 04 OS, 12610624 is an 07 OS

Re: PCM Hammer P12 development

Posted: Mon Jan 16, 2023 6:10 pm
by bill12690
spyder09 wrote: 12597978 is an 04 OS, 12610624 is an 07 OS
Sorry, wrong BIN somehow attached. Edited and uploaded the correct BIN. This is from an 04, not an 07. I'm actually not sure at the moment where exactly I even found the 07 BIN.
edit: the 07 bin was another LSJ car, but found on the gearhead-efi forum. I evidently just clicked the wrong one at the original upload.

Re: PCM Hammer P12 development

Posted: Thu May 25, 2023 12:51 pm
by Lowlyfe1
Here is the file from a twincharged setup Im working on with a friend its from a 2006 ion redline operating system 12598284