Unable to read P01 PCM with PCMHammer or HPTuners

They go by many names, P01, P10, P12, P59, E38, VPW, '0411 etc.
Post Reply
bradtpt
Posts: 1
Joined: Wed Jul 27, 2011 8:19 am

Unable to read P01 PCM with PCMHammer or HPTuners

Post by bradtpt »

Hi guys,

I have a P01 PCM here that I cannot read. Have tried with HPTuners and I get a "Reader upload: invalid checksum" error (see attached image). I tried with PCMHammer and it uploads the kernel to begin ok, then immediately stops, log below:

Code: Select all

[04:37:08:019]  PCM Hammer 021.2
[04:37:08:020]  Friday, December 20 2024 @04:37:08:02
[04:37:09:017]  Voltage: 12.8V
[04:37:09:034]  Elm ID: ELM327 v1.4b
[04:37:09:066]  ScanTool device ID: STN2230 v5.8.1
[04:37:19:496]  Read canceled.
[04:37:30:200]  Will save to Z:\customerfilename.bin
[04:37:40:330]  Querying operating system of current PCM.
[04:37:40:461]  OSID: 1273003
[04:37:40:621]  Unlock succeeded.
[04:37:40:682]  This interface does not support VPW 4x
[04:37:41:727]  Kernel upload 9% complete.
[04:37:42:920]  Kernel upload 22% complete.
[04:37:44:111]  Kernel upload 35% complete.
[04:37:45:215]  Kernel upload 48% complete.
[04:37:46:400]  Kernel upload 61% complete.
[04:37:47:532]  Kernel upload 74% complete.
[04:37:48:689]  Kernel upload 87% complete.
[04:37:49:825]  Kernel upload 100% complete.
[04:37:51:250]  Kernel Version: 01030501
[04:37:51:259]  kernel uploaded to PCM succesfully. Requesting data...
[04:37:51:360]  Flash chip: Intel 28F400B, 512kb
[04:37:51:374]  Read complete.
[04:37:51:381]  All read-request messages succeeded on the first try. You have an excellent connection to the PCM.
[04:37:51:389]  We're not sure how much retrying is normal for a read operation on a 0kb PCM.
[04:37:51:396]  Please help by sharing your results in the PCM Hammer thread at pcmhacking.net.
[04:37:51:405]  Starting verification...
[04:37:51:413]  Calculating CRCs from file.
[04:37:51:419]  Initializing CRC algorithm on PCM, this will take a minute...
[04:37:51:556]  Requesting CRCs from PCM.
[04:37:51:582]  	Range		File CRC		PCM CRC	Verdict	Purpose
[04:37:51:592]  060000-07FFFF	not needed	not needed	n/a	OperatingSystem
[04:37:51:603]  040000-05FFFF	not needed	not needed	n/a	OperatingSystem
[04:37:51:616]  020000-03FFFF	not needed	not needed	n/a	OperatingSystem
[04:37:51:630]  008000-01FFFF	not needed	not needed	n/a	Calibration
[04:37:51:651]  006000-007FFF	not needed	not needed	n/a	Parameter
[04:37:51:661]  004000-005FFF	not needed	not needed	n/a	Parameter
[04:37:51:670]  000000-003FFF	not needed	not needed	n/a	Boot
[04:37:51:726]  The contents of the file match the contents of the PCM.
[04:37:51:854]  Clearing trouble codes.
[04:37:53:970]  Clearing trouble codes.
[04:37:56:071]  Elapsed time 00:00:15.4438276
[04:37:56:092]  Saving contents to Z:\customerfilename.bin
Debug log:

Code: Select all

[04:59:38:680]  PCM Hammer 021.2
[04:59:38:681]  Friday, December 20 2024 @04:59:38:68
[04:59:38:684]  ElmDevice initialization starting.
[04:59:38:819]  TX: 
[04:59:38:834]  TX: AT Z
[04:59:39:732]  ELM327 v1.4b
[04:59:39:734]  TX: AT E0
[04:59:39:747]  AT E0  OK
[04:59:39:750]  TX: AT S0
[04:59:39:763]  OK
[04:59:39:765]  TX: AT RV
[04:59:39:779]  Voltage: 12.8V
[04:59:39:783]  TX: AT I
[04:59:39:796]  Elm ID: ELM327 v1.4b
[04:59:39:800]  Initializing PcmHacking.AllProDeviceImplementation
[04:59:39:804]  TX: AT #1
[04:59:39:811]  This is not an AllPro device.
[04:59:39:815]  Determining whether PcmHacking.ScanToolDeviceImplementation is connected.
[04:59:39:818]  TX: ST I
[04:59:39:828]  ScanTool device ID: STN2230 v5.8.1
[04:59:39:832]  TX: STPTO 3000
[04:59:39:843]  OK
[04:59:39:848]  TX: AT AL
[04:59:39:859]  OK
[04:59:39:862]  TX: AT SP2
[04:59:39:875]  OK
[04:59:39:880]  TX: AT DP
[04:59:39:891]  SAE J1850 VPW
[04:59:39:896]  TX: AT AR
[04:59:39:907]  OK
[04:59:39:912]  TX: AT AT0
[04:59:39:923]  OK
[04:59:39:928]  TX: AT SR F0
[04:59:39:939]  OK
[04:59:39:943]  TX: AT H1
[04:59:39:955]  OK
[04:59:39:959]  TX: AT ST 20
[04:59:39:971]  OK
[04:59:53:657]  Will save to Z:\customerfile.bin
[05:00:03:736]  Querying operating system of current PCM.
[05:00:03:766]  Setting timeout for ReadProperty, 25 ms.
[05:00:03:774]  TX: STPTO 25
[05:00:03:791]  OK
[05:00:03:795]  TX: STPX H:6C10F0, R:1, D:3C0A
[05:00:03:905]  RX: 6C F0 10 7C 0A 00 13 6C AB
[05:00:03:920]  OSID: 1273003
[05:00:03:940]  Suppressing VPW chatter.
[05:00:03:952]  TX: STPX H:6CFEF0, R:1, D:2800
[05:00:03:999]  RX: 6C F0 10 68 00
[05:00:04:008]  Sending 'test device present' notification.
[05:00:04:018]  Setting timeout for Minimum, 0 ms.
[05:00:04:027]  TX: STPTO 0
[05:00:04:047]  OK
[05:00:04:053]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:04:079]  Empty response to STPX with data. OK.
[05:00:04:084]  Setting timeout for ReadProperty, 25 ms.
[05:00:04:090]  TX: STPTO 25
[05:00:04:111]  OK
[05:00:04:116]  Ignoring chatter: 6C F0 10 68 00
[05:00:04:120]  Sending seed request.
[05:00:04:126]  TX: STPX H:6C10F0, R:1, D:2701
[05:00:04:175]  RX: 6C F0 10 67 01 3D CD
[05:00:04:184]  Parsing seed value.
[05:00:04:196]  Sending unlock request (3DCD, C610)
[05:00:04:209]  TX: STPX H:6C10F0, R:1, D:2702C610
[05:00:04:257]  RX: 6C F0 10 67 02 34
[05:00:04:264]  Unlock succeeded.
[05:00:04:271]  Sending 'test device present' notification.
[05:00:04:277]  Setting timeout for Minimum, 0 ms.
[05:00:04:284]  TX: STPTO 0
[05:00:04:303]  OK
[05:00:04:307]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:04:335]  Empty response to STPX with data. OK.
[05:00:04:339]  Setting timeout for ReadProperty, 25 ms.
[05:00:04:347]  TX: STPTO 25
[05:00:04:367]  OK
[05:00:04:371]  This interface does not support VPW 4x
[05:00:04:376]  Sending 'test device present' notification.
[05:00:04:383]  Setting timeout for Minimum, 0 ms.
[05:00:04:388]  TX: STPTO 0
[05:00:04:399]  OK
[05:00:04:404]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:04:431]  Empty response to STPX with data. OK.
[05:00:04:437]  Setting timeout for ReadProperty, 25 ms.
[05:00:04:443]  TX: STPTO 25
[05:00:04:463]  OK
[05:00:04:469]  Loaded C:\Users\user\Downloads\PcmHammer021.2\PcmHammer021.2\Kernel-P01.bin
[05:00:04:474]  Sending 'test device present' notification.
[05:00:04:485]  Setting timeout for Minimum, 0 ms.
[05:00:04:496]  TX: STPTO 0
[05:00:04:512]  OK
[05:00:04:519]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:04:543]  Empty response to STPX with data. OK.
[05:00:04:548]  Setting timeout for ReadProperty, 25 ms.
[05:00:04:554]  TX: STPTO 25
[05:00:04:575]  OK
[05:00:04:580]  Sending upload request for kernel size 7890, loadaddress FF8000
[05:00:04:586]  TX: STPX H:6C10F0, R:1, D:34001000FF8000
[05:00:04:625]  RX: 6C F0 10 74 00 44
[05:00:04:629]  Going to load a 7890 byte kernel to 0xFF8000
[05:00:04:637]  Setting timeout for SendKernel, 50 ms.
[05:00:04:644]  TX: STPTO 50
[05:00:04:656]  OK
[05:00:04:662]  Sending end block payload with offset 0x1C00, start address 0xFF9C00, length 0x2D2.
[05:00:04:670]  Sending 'test device present' notification.
[05:00:04:676]  Setting timeout for Minimum, 0 ms.
[05:00:04:683]  TX: STPTO 0
[05:00:04:704]  OK
[05:00:04:708]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:04:736]  Empty response to STPX with data. OK.
[05:00:04:740]  Setting timeout for SendKernel, 50 ms.
[05:00:04:746]  TX: STPTO 50
[05:00:04:768]  OK
[05:00:04:834]  TX: STPX H:6D10F0, R:1, L:731
[05:00:04:864]  TX: 360002D2FF9C0030BC5555203C00000AAA204030BC9090428020403F50000A700220403F5000084280302F000A2200484142414280302F0008240184802F4200044280204030BCFFFF203C00FFFA4E204030BC1060202F0004241F508F4E75518F518F426F000E2F6F00140006203C00FFFA4E204030BC7060203C00000AAA204030BCAAAA203C00000554204030BC5555203C00000AAA204030BC8080203C00000AAA204030BCAAAA203C00000554204030BC5555202F0006204030BC3030426F0004426F000242AF000A6058202F0006204030103200024100403F4100044EB900FF8BDC202F0006204030103200024100403F410002302F0002B06F00046602602C202F0006204030103200024100203E814A57660652AF000A60083F7C00A0000E600A0CAF0127FFFF000A6F9E0C6F00A0000E663A202F0006204030103200024100403F410004202F0006204030103200024100403F410002302F0002B06F000467083F7C00B0000E6004426F000E202F0006204030BCF0F0202F0006204030BCF0F0203C00FFFA4E204030BC1060302F000E1000508F508F4E754FEFFFE0422F00152F6F002C00102F6F0028000C42AF001C600000E6202F001CD080222F000CD2802F410008202F001CD080D0AF001020403F5000064AAF0030663A203C00FFFA4E204030BC7060203C00000AAA204030BCAAAA203C00000554204030BC5555203C00000AAA204030BCA0A0202F0008204030AF0006422F001B42AF001660344EB900FF8BDC4AAF0030660A202F0008204030106004302F00063F400004302F0006B06F000466081F7C0001001B600E52AF00160CAF00000FFF00166FC24A2F001B66321F7CFFAA00154AAF00306620202F0008204030BCF0F0202F0008204030BCF0F0203C00FFFA4E204030BC1060102F0015603A52AF001C202F0024E288B0AF001C6200FF104AAF003066202EAF00282017204030BCF0F02017204030BCF0F0203C00FFFA4E204030BC106042004FEF00204E75BFA9
[05:00:05:635]  RX: 6D F0 10 76 00 73
[05:00:05:650]  Found response, Success
[05:00:05:660]  Kernel upload 9% complete.
[05:00:05:673]  Sending block with offset 0x001800, start address 0xFF9800, length 0x0400.
[05:00:05:736]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:00:06:819]  RX: 6D F0 10 76 00 73
[05:00:06:838]  Found response, Success
[05:00:06:852]  Kernel upload 22% complete.
[05:00:06:862]  Sending block with offset 0x001400, start address 0xFF9400, length 0x0400.
[05:00:06:871]  Sending 'test device present' notification.
[05:00:06:880]  Setting timeout for Minimum, 0 ms.
[05:00:06:886]  TX: STPTO 0
[05:00:06:897]  OK
[05:00:06:903]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:06:928]  Empty response to STPX with data. OK.
[05:00:06:933]  Setting timeout for SendKernel, 50 ms.
[05:00:06:940]  TX: STPTO 50
[05:00:06:961]  OK
[05:00:07:041]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:00:08:100]  RX: 6D F0 10 76 00 73
[05:00:08:119]  Found response, Success
[05:00:08:132]  Kernel upload 35% complete.
[05:00:08:142]  Sending block with offset 0x001000, start address 0xFF9000, length 0x0400.
[05:00:08:215]  TX: STPX H:6D10F0, R:1, L:1033
[05:00:08:242]  TX: 36000400FF90000008606E203C00FFF60F20401210202F001020401081203C00FFF60C204010BC00024AAF000466026048202F00102040101010000280000000FF7230C0814A80670E202F0014204010BC000242806026202F0014204010BC0001202F000460164E71202F0014204010BC000B428060064E716000FEDA508F588F4E75598F202F000C53802E80602A2017D0AF00102217D2AF000820411210118109B000FF9ED620170280000001FF4A8066044EBAFB2E53974A976CD2588F4E754EBAFB9813FC006C00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC006000FF9ED9202F00047218E2A8100013C000FF9EDA202F0004028000FF000042404840100013C000FF9EDB202F000402800000FF00E088100013C000FF9EDC202F0004100013C000FF9EDD4878000548780008487900FF9ED64EBAFC58508F588F4EBAFB1860FE518F518F2F02226F0018206F001C222F0020202F002434091F42000A34081F4200081F4100061F4000041F7CFF8C000C1F7CFFFE000D1F7CFFF0000E1F7C003F000F1F6F000A00101F6F000800111F6F000600121F6F0004001348780005487800087014D08F2F004EBAFBE2508F588F241F508F508F4E752F02202F0008100010000280000000FF2240202F000802800000FF00E088100010000280000000FF2040202F0008028000FF000042404840100042811200202F00087418E4A8100010000280000000FF2F092F082F012F004EBAFF2E508F508F241F4E75518F426F000670042F400002601C202F0002068000FF9ED6204010101000024000FFD16F000652AF00027009B0AF00026CDC302F0006508F4E75518F2F024EBAF980426F000A42AF00066056202F0006D0AF001020401F5000054240102F0005D16F000A222F000624014C3C2C0051EB851FEA802401D482958220429088E5882400E58A2042D0882400E58A2042D0882401948020024A8066044EBAF92452AF0006202F0006B0AF001465A04EBAF912302F000A241F508F4E75598F202F000C3F400002700AD0AF0008322F0002E0491201118109B000FF9ED6700BD0AF0008322F00021201118109B000FF9ED6588F4E7513FC006C00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC007D00FF9ED9423900FF9EDA13FC000100FF9EDB13FC000300FF9EDC13FC000500FF9EDD13FC000100FF9EDE4EBAF90E4878000548780009487900FF9ED64EBAFA24508F588F4E75518F103900FF9EDB10000280000000FF2200E189103900FF9EDC10000280000000FFD0812F400004103900FF9EDD10000280000000FF220048414241103900FF9EDE10000280000000FFE188D280103900FF9EDF10000280000000FFD0812E8013FC006D00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC003600FF9ED913FC000100FF9EDA202F0004E088100048AC
[05:00:09:285]  RX: 6D F0 10 76 00 73
[05:00:09:305]  Found response, Success
[05:00:09:324]  Kernel upload 48% complete.
[05:00:09:338]  Sending block with offset 0x000C00, start address 0xFF8C00, length 0x0400.
[05:00:09:351]  Sending 'test device present' notification.
[05:00:09:361]  Setting timeout for Minimum, 0 ms.
[05:00:09:368]  TX: STPTO 0
[05:00:09:394]  OK
[05:00:09:406]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:09:426]  Empty response to STPX with data. OK.
[05:00:09:434]  Setting timeout for SendKernel, 50 ms.
[05:00:09:444]  TX: STPTO 50
[05:00:09:458]  OK
[05:00:09:532]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:00:10:626]  RX: 6D F0 10 76 00 73
[05:00:10:645]  Found response, Success
[05:00:10:665]  Kernel upload 61% complete.
[05:00:10:679]  Sending block with offset 0x000800, start address 0xFF8800, length 0x0400.
[05:00:10:754]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:00:11:845]  RX: 6D F0 10 76 00 73
[05:00:11:865]  Found response, Success
[05:00:11:879]  Kernel upload 74% complete.
[05:00:11:891]  Sending block with offset 0x000400, start address 0xFF8400, length 0x0400.
[05:00:11:899]  Sending 'test device present' notification.
[05:00:11:909]  Setting timeout for Minimum, 0 ms.
[05:00:11:917]  TX: STPTO 0
[05:00:11:939]  OK
[05:00:11:945]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:11:971]  Empty response to STPX with data. OK.
[05:00:11:985]  Setting timeout for SendKernel, 50 ms.
[05:00:11:997]  TX: STPTO 50
[05:00:12:019]  OK
[05:00:12:085]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:00:13:156]  RX: 6D F0 10 76 00 73
[05:00:13:180]  Found response, Success
[05:00:13:199]  Kernel upload 87% complete.
[05:00:13:219]  Sending block with offset 0x000000, start address 0xFF8000, length 0x0400.
[05:00:13:296]  TX: STPX H:6D10F0, R:1, L:1033
[05:00:13:331]  TX: 36800400FF80004FEFFFE8007C07004EB900FF8BDC203C00FFF606204042104EB900FF8984203C00FFF60C204010BC0003203C00FFF60D204042104EB900FF8C864EB900FF8C0E4EB900FF8BDC42A74EB900FF9568588F487800044878000348780002487800014EB900FF9140508F508F4EB900FF8C5442AF00142F7C000009C4000C202F001490AF000C220052812F410008202F001490AF000C2F40001052AF00144EB900FF8BDC50EF000350EF0002200F54802F00200F5E802F004EB900FF8F3C508F2F4000044AAF00046632202F0010D0AF000CB0AF001464224878007748780066487800734878006E4EB900FF9140508F508F2F6F0014001060626060102F000349C07230C0814A8067026050102F00020C000001672C102F000242811200102F000210000280000000FF2F012F00487800BB487800BB4EB900FF9140508F508F601A2F6F001400082F6F00140010202F00142F004EB900FF87A2588F6000FF3C0000518F2F02226F0010206F0014222F0018202F001C34091F42000A34081F4200081F4100061F40000413FC006C00FF9ED613FCFFF000FF9ED713FC001000FF9ED84A2F000A672213FC007D00FF9ED913EF000800FF9EDA13EF000600FF9EDB13EF000400FF9EDC602813FC007F00FF9ED913FC003D00FF9EDA13EF000800FF9EDB13EF000600FF9EDC13EF000400FF9EDD4A2F000A6704700760027008487800052F00487900FF9ED64EB900FF8D8C508F588F241F508F4E754EB900FF8BDC4EB900FF996E23C000FF9ED24EB900FF8BDC203900FF9ED2424048400C8000000089670C4EB900FF9BC423C000FF9ED24EB900FF8BDC487800014EB900FF8C74588F13FC006C00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC007D00FF9ED913FC000100FF9EDA203900FF9ED27218E2A8100013C000FF9EDB203900FF9ED242404840100013C000FF9EDC203900FF9ED2E088100013C000FF9EDD203900FF9ED2100013C000FF9EDE4878000548780009487900FF9ED64EB900FF8D8C508F588F4E754FEFFFE8103900FF9EDB10000280000000FF220048414241103900FF9EDC10000280000000FFE188D280103900FF9EDD10000280000000FFD0812F400012103900FF9EDE10000280000000FF220048414241103900FF9EDF10000280000000FFE188D280103900FF9EE010000280000000FFD0812F40000E2F6F000E000A2F6F001200062F2F00062F2F000E4EB900FF8AA4508F4A8066181F7C000100172F2F00062F2F000E4EB900FF8AF2508F600C1F7C000200174EB900FF8B184EB900FF8C642F2F00062F2F000E4EB900FF8AC8508F4A80670000E84EB900FF8B102F40000213FC006C00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC007D00FF9ED913FC000200FF9EDA203900FFB356484048C0100013C000FF9EDB6FB0
[05:00:14:359]  RX: 6D F0 10 76 00 73
[05:00:14:370]  Found response, Success
[05:00:14:379]  Kernel upload 100% complete.
[05:00:14:390]  TX: STPX H:6C10F0, R:1, D:3D00
[05:00:15:521]  Timeout during receive.
[05:00:15:644]  TX: STPX H:6C10F0, R:1, D:3D00
[05:00:15:688]  RX: 6C F0 10 7D 00 01 03 05 01
[05:00:15:708]  Kernel Version: 01030501
[05:00:15:722]  kernel uploaded to PCM succesfully. Requesting data...
[05:00:15:734]  Sending 'test device present' notification.
[05:00:15:745]  Setting timeout for Minimum, 0 ms.
[05:00:15:754]  TX: STPTO 0
[05:00:15:764]  OK
[05:00:15:771]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:15:797]  Empty response to STPX with data. OK.
[05:00:15:802]  Setting timeout for SendKernel, 50 ms.
[05:00:15:808]  TX: STPTO 50
[05:00:15:829]  OK
[05:00:15:834]  Setting timeout for ReadProperty, 25 ms.
[05:00:15:842]  TX: STPTO 25
[05:00:15:861]  OK
[05:00:15:865]  TX: STPX H:6C10F0, R:1, D:3D01
[05:00:15:909]  RX: 6C F0 10 7D 01 00 89 44 71
[05:00:15:920]  Flash chip: Intel 28F400B, 512kb
[05:00:15:929]  Setting timeout for ReadMemoryBlock, 250 ms.
[05:00:15:937]  TX: STPTO 250
[05:00:15:957]  OK
[05:00:15:962]  Read complete.
[05:00:15:969]  All read-request messages succeeded on the first try. You have an excellent connection to the PCM.
[05:00:15:974]  We're not sure how much retrying is normal for a read operation on a 0kb PCM.
[05:00:15:980]  Please help by sharing your results in the PCM Hammer thread at pcmhacking.net.
[05:00:15:986]  Starting verification...
[05:00:15:992]  Calculating CRCs from file.
[05:00:15:997]  Initializing CRC algorithm on PCM, this will take a minute...
[05:00:16:004]  Sending 'test device present' notification.
[05:00:16:011]  Setting timeout for Minimum, 0 ms.
[05:00:16:019]  TX: STPTO 0
[05:00:16:037]  OK
[05:00:16:042]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:16:069]  Empty response to STPX with data. OK.
[05:00:16:073]  Setting timeout for ReadMemoryBlock, 250 ms.
[05:00:16:080]  TX: STPTO 250
[05:00:16:101]  OK
[05:00:16:106]  TX: STPX H:6C10F0, R:1, D:3D02000000000000
[05:00:16:203]  RX: 6C F0 10 7D 02 00 00 00 00 00 00 00 00 00 00
[05:00:16:220]  Requesting CRCs from PCM.
[05:00:16:239]  Setting timeout for ReadCrc, 100 ms.
[05:00:16:255]  TX: STPTO 100
[05:00:16:277]  OK
[05:00:16:287]  	Range		File CRC		PCM CRC	Verdict	Purpose
[05:00:16:309]  060000-07FFFF	not needed	not needed	n/a	OperatingSystem
[05:00:16:324]  040000-05FFFF	not needed	not needed	n/a	OperatingSystem
[05:00:16:338]  020000-03FFFF	not needed	not needed	n/a	OperatingSystem
[05:00:16:348]  008000-01FFFF	not needed	not needed	n/a	Calibration
[05:00:16:357]  006000-007FFF	not needed	not needed	n/a	Parameter
[05:00:16:365]  004000-005FFF	not needed	not needed	n/a	Parameter
[05:00:16:374]  000000-003FFF	not needed	not needed	n/a	Boot
[05:00:16:388]  Sending 'test device present' notification.
[05:00:16:396]  Setting timeout for Minimum, 0 ms.
[05:00:16:407]  TX: STPTO 0
[05:00:16:437]  OK
[05:00:16:445]  TX: STPX H:8CFEF0, R:0, D:3F
[05:00:16:469]  Empty response to STPX with data. OK.
[05:00:16:487]  Setting timeout for ReadCrc, 100 ms.
[05:00:16:499]  TX: STPTO 100
[05:00:16:517]  OK
[05:00:16:525]  The contents of the file match the contents of the PCM.
[05:00:16:537]  Halting the kernel.
[05:00:16:547]  TX: STPX H:6C10F0, R:1, D:20
[05:00:16:678]  Clearing trouble codes.
[05:00:16:707]  Setting timeout for Minimum, 0 ms.
[05:00:16:721]  TX: STPTO 0
[05:00:16:741]  OK
[05:00:17:013]  TX: STPX H:686AF0, R:1, D:04
[05:00:18:056]  Empty response to STPX with data. That's not OK.
[05:00:18:351]  TX: STPX H:686AF0, R:1, D:04
[05:00:18:391]  Unexpected response to STPX with data: STOPPED
[05:00:18:664]  TX: STPX H:8CFEF0, R:1, D:14
[05:00:18:673]  Unexpected response to STPX with data: ?
[05:00:18:941]  TX: STPX H:8CFEF0, R:1, D:14
[05:00:18:975]  RX: 8C F0 10 54
[05:00:18:995]  Halting the kernel.
[05:00:19:014]  TX: STPX H:6C10F0, R:1, D:20
[05:00:19:063]  RX: 6C F0 10 60
[05:00:19:073]  Clearing trouble codes.
[05:00:19:344]  TX: STPX H:686AF0, R:1, D:04
[05:00:20:383]  Empty response to STPX with data. That's not OK.
[05:00:20:678]  TX: STPX H:686AF0, R:1, D:04
[05:00:20:695]  Unexpected response to STPX with data: STOPPED
[05:00:20:960]  TX: STPX H:8CFEF0, R:1, D:14
[05:00:20:977]  Unexpected response to STPX with data: ?
[05:00:21:256]  TX: STPX H:8CFEF0, R:1, D:14
[05:00:21:290]  RX: 8C F0 10 54
[05:00:21:307]  Elapsed time 00:00:17.0362303
[05:00:21:323]  Saving contents to Z:\customerfile.bin
To glean further info, I tried a "test write" in PCMHammer and I note it reports the flash memory size as 0Kb. Anybody know of a workaround so I can read this out? I always take a "before" snapshot of my jobs. I was going to attempt to write a complete 12225074 over the top and start again but would prefer to have the benefit of an undo button like I always leave myself.

Code: Select all

[04:52:21:829]  Z:\12225074.bin
[04:52:22:326]  Validating 512k file.
[04:52:22:339]  	Start	End	Stored	Needed	Verdict	Segment Name
[04:52:22:360]  	00000	7FFFD	0BA1	0BA1	Good	Operating system
[04:52:22:372]  	08002	13FFF	DA66	DA66	Good	Engine calibration
[04:52:22:386]  	14002	16DFF	AFB4	AFB4	Good	Engine diagnostics.
[04:52:22:401]  	16E02	1BDFF	DDC0	DDC0	Good	Transmission calibration
[04:52:22:416]  	1BE02	1C7FF	94CA	94CA	Good	Transmission diagnostics
[04:52:22:431]  	1C802	1E51F	12F6	12F6	Good	Fuel system
[04:52:22:449]  	1E522	1EE9F	16CD	16CD	Good	System
[04:52:22:465]  	1EEA2	1EF9F	A33D	A33D	Good	Speedometer
[04:52:22:481]  Requesting operating system ID...
[04:52:22:537]  PCM and file are both for the same Hardware P01_P59
[04:52:22:551]  Operating system IDs do not match.
[04:52:22:569]  PCM operating system ID: 1273003
[04:52:22:587]  File operating system ID: 12225074
[04:52:22:606]  PCM and image file are different operating systems.
[04:52:22:623]  But we'll ignore that because this is just a test write.
[04:52:22:809]  Unlock succeeded.
[04:52:22:886]  This interface does not support VPW 4x
[04:52:23:820]  Kernel upload 9% complete.
[04:52:24:972]  Kernel upload 22% complete.
[04:52:26:173]  Kernel upload 35% complete.
[04:52:27:340]  Kernel upload 48% complete.
[04:52:28:542]  Kernel upload 61% complete.
[04:52:29:693]  Kernel upload 74% complete.
[04:52:30:878]  Kernel upload 87% complete.
[04:52:32:045]  Kernel upload 100% complete.
[04:52:33:359]  Kernel Version: 01030501
[04:52:33:403]  Kernel uploaded to PCM succesfully.
[04:52:33:522]  PCM and image file are different operating systems.
[04:52:33:556]  But we'll ignore that because this is just a test write.
[04:52:33:712]  Flash chip: Intel 28F400B, 512kb
[04:52:33:762]  File size 524,288 does not match PCM size 0. This image is not compatible with this PCM.
[04:52:33:835]  Clearing trouble codes.
[04:52:36:031]  Elapsed time 00:00:13.1837003
Debug log:

Code: Select all

[05:02:20:551]  PCM Hammer 021.2
[05:02:20:553]  Friday, December 20 2024 @05:02:20:55
[05:02:20:557]  ElmDevice initialization starting.
[05:02:20:689]  TX: 
[05:02:20:707]  TX: AT Z
[05:02:21:616]  ELM327 v1.4b
[05:02:21:624]  TX: AT E0
[05:02:21:645]  AT E0  OK
[05:02:21:652]  TX: AT S0
[05:02:21:677]  OK
[05:02:21:684]  TX: AT RV
[05:02:21:709]  Voltage: 12.8V
[05:02:21:715]  TX: AT I
[05:02:21:725]  Elm ID: ELM327 v1.4b
[05:02:21:732]  Initializing PcmHacking.AllProDeviceImplementation
[05:02:21:735]  TX: AT #1
[05:02:21:757]  This is not an AllPro device.
[05:02:21:763]  Determining whether PcmHacking.ScanToolDeviceImplementation is connected.
[05:02:21:770]  TX: ST I
[05:02:21:790]  ScanTool device ID: STN2230 v5.8.1
[05:02:21:797]  TX: STPTO 3000
[05:02:21:805]  OK
[05:02:21:808]  TX: AT AL
[05:02:21:820]  OK
[05:02:21:826]  TX: AT SP2
[05:02:21:853]  OK
[05:02:21:860]  TX: AT DP
[05:02:21:886]  SAE J1850 VPW
[05:02:21:897]  TX: AT AR
[05:02:21:917]  OK
[05:02:21:923]  TX: AT AT0
[05:02:21:949]  OK
[05:02:21:954]  TX: AT SR F0
[05:02:21:965]  OK
[05:02:21:970]  TX: AT H1
[05:02:21:981]  OK
[05:02:21:987]  TX: AT ST 20
[05:02:21:997]  OK
[05:02:37:356]  Z:\12225074.bin
[05:02:37:806]  Validating 512k file.
[05:02:37:811]  Trying P01 512Kb
[05:02:37:815]  	Start	End	Stored	Needed	Verdict	Segment Name
[05:02:37:825]  	00000	7FFFD	0BA1	0BA1	Good	Operating system
[05:02:37:843]  	08002	13FFF	DA66	DA66	Good	Engine calibration
[05:02:37:863]  	14002	16DFF	AFB4	AFB4	Good	Engine diagnostics.
[05:02:37:872]  	16E02	1BDFF	DDC0	DDC0	Good	Transmission calibration
[05:02:37:887]  	1BE02	1C7FF	94CA	94CA	Good	Transmission diagnostics
[05:02:37:903]  	1C802	1E51F	12F6	12F6	Good	Fuel system
[05:02:37:932]  	1E522	1EE9F	16CD	16CD	Good	System
[05:02:37:955]  	1EEA2	1EF9F	A33D	A33D	Good	Speedometer
[05:02:37:976]  Requesting operating system ID...
[05:02:37:993]  Setting timeout for ReadProperty, 25 ms.
[05:02:38:006]  TX: STPTO 25
[05:02:38:021]  OK
[05:02:38:040]  TX: STPX H:6C10F0, R:1, D:3C0A
[05:02:38:165]  RX: 6C F0 10 7C 0A 00 13 6C AB
[05:02:38:179]  Trying P01 512Kb
[05:02:38:202]  PCM and file are both for the same Hardware P01_P59
[05:02:38:219]  Trying P01 512Kb
[05:02:38:242]  Operating system IDs do not match.
[05:02:38:273]  PCM operating system ID: 1273003
[05:02:38:290]  File operating system ID: 12225074
[05:02:38:312]  Trying P01 512Kb
[05:02:38:335]  PCM and image file are different operating systems.
[05:02:38:357]  But we'll ignore that because this is just a test write.
[05:02:38:382]  Suppressing VPW chatter.
[05:02:38:403]  TX: STPX H:6CFEF0, R:1, D:2800
[05:02:38:455]  RX: 6C F0 10 68 00
[05:02:38:469]  Sending 'test device present' notification.
[05:02:38:478]  Setting timeout for Minimum, 0 ms.
[05:02:38:502]  TX: STPTO 0
[05:02:38:518]  OK
[05:02:38:539]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:38:581]  Empty response to STPX with data. OK.
[05:02:38:595]  Setting timeout for ReadProperty, 25 ms.
[05:02:38:613]  TX: STPTO 25
[05:02:38:629]  OK
[05:02:38:645]  Ignoring chatter: 6C F0 10 68 00
[05:02:38:669]  Sending seed request.
[05:02:38:679]  TX: STPX H:6C10F0, R:1, D:2701
[05:02:38:727]  RX: 6C F0 10 67 01 3D CD
[05:02:38:743]  Parsing seed value.
[05:02:38:769]  Sending unlock request (3DCD, C610)
[05:02:38:779]  TX: STPX H:6C10F0, R:1, D:2702C610
[05:02:38:823]  RX: 6C F0 10 67 02 34
[05:02:38:834]  Unlock succeeded.
[05:02:38:865]  Sending 'test device present' notification.
[05:02:38:876]  Setting timeout for Minimum, 0 ms.
[05:02:38:892]  TX: STPTO 0
[05:02:38:918]  OK
[05:02:38:933]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:38:966]  Empty response to STPX with data. OK.
[05:02:38:973]  Setting timeout for ReadProperty, 25 ms.
[05:02:38:982]  TX: STPTO 25
[05:02:38:998]  OK
[05:02:39:004]  This interface does not support VPW 4x
[05:02:39:010]  Loaded C:\Users\user\Downloads\PcmHammer021.2\PcmHammer021.2\Kernel-P01.bin
[05:02:39:017]  Sending upload request for kernel size 7890, loadaddress FF8000
[05:02:39:026]  TX: STPX H:6C10F0, R:1, D:34001000FF8000
[05:02:39:079]  RX: 6C F0 10 74 00 44
[05:02:39:084]  Going to load a 7890 byte kernel to 0xFF8000
[05:02:39:100]  Setting timeout for SendKernel, 50 ms.
[05:02:39:115]  TX: STPTO 50
[05:02:39:126]  OK
[05:02:39:145]  Sending end block payload with offset 0x1C00, start address 0xFF9C00, length 0x2D2.
[05:02:39:157]  Sending 'test device present' notification.
[05:02:39:168]  Setting timeout for Minimum, 0 ms.
[05:02:39:172]  TX: STPTO 0
[05:02:39:189]  OK
[05:02:39:197]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:39:222]  Empty response to STPX with data. OK.
[05:02:39:226]  Setting timeout for SendKernel, 50 ms.
[05:02:39:231]  TX: STPTO 50
[05:02:39:254]  OK
[05:02:39:329]  TX: STPX H:6D10F0, R:1, L:731
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
[05:02:40:089]  RX: 6D F0 10 76 00 73
[05:02:40:105]  Found response, Success
[05:02:40:124]  Kernel upload 9% complete.
[05:02:40:140]  Sending block with offset 0x001800, start address 0xFF9800, length 0x0400.
[05:02:40:242]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:02:41:337]  RX: 6D F0 10 76 00 73
[05:02:41:359]  Found response, Success
[05:02:41:378]  Kernel upload 22% complete.
[05:02:41:388]  Sending block with offset 0x001400, start address 0xFF9400, length 0x0400.
[05:02:41:402]  Sending 'test device present' notification.
[05:02:41:408]  Setting timeout for Minimum, 0 ms.
[05:02:41:419]  TX: STPTO 0
[05:02:41:447]  OK
[05:02:41:458]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:41:495]  Empty response to STPX with data. OK.
[05:02:41:501]  Setting timeout for SendKernel, 50 ms.
[05:02:41:518]  TX: STPTO 50
[05:02:41:543]  OK
[05:02:41:620]  TX: STPX H:6D10F0, R:1, L:1033
[05:02:41:644]  TX: 36000400FF940013C000FF9EDB202F0004100013C000FF9EDC201742404840100013C000FF9EDD2017E088100013C000FF9EDE2017100013C000FF9EDF4EB900FF8C64487800014878000A487900FF9ED64EB900FF8D8C508F588F202F00043000300002800000FFFF22174878000C2F002F014EB900FF8D8C508F588F508F4E75518F103900FF9EDB10000280000000FF2200E189103900FF9EDC10000280000000FFD0812F400004103900FF9EDD10000280000000FF220048414241103900FF9EDE10000280000000FFE188D280103900FF9EDF10000280000000FFD0812E800CAF000010000004634213FC006C00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC007F00FF9ED913FC003400FF9EDA4878000548780005487900FF9ED64EB900FF8D8C508F588F603E13FC006C00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC007400FF9ED9423900FF9EDA4878000548780005487900FF9ED64EB900FF8D8C508F588F508F4E75598F202F00081F40000213FC006D00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC007600FF9ED913EF000200FF9EDA4878000548780005487900FF9ED64EB900FF8D8C508F588F588F4E75598F222F0008202F000C1F4100021E8013FC006D00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC007F00FF9ED913FC003600FF9EDA13EF000200FF9EDB13D700FF9EDC4878000548780007487900FF9ED64EB900FF8D8C508F588F588F4E754FEFFFE02F021F7900FF9EDA0019103900FF9EDB10000280000000FF2200E189103900FF9EDC10000280000000FFD0812F400014103900FF9EDD10000280000000FF220048414241103900FF9EDE10000280000000FFE188D280103900FF9EDF10000280000000FFD0812F400010426F002270042F40001E6030202F001E0280000003FF4A8066064EB900FF8BDC202F001E068000FF9ED6204010101000024000FFD16F002252AF001E700AD0AF0014B0AF001E62C4700AD0AF0014103009B000FF9ED610000280000000FFE1883200700BD0AF0014103009B000FF9ED61000024000FF80413F40000E302F000EB06F00226700009413FC006D00FF9ED613FCFFF000FF9ED713FC001000FF9ED813FC007F00FF9ED913FC003600FF9EDA302F0022E048100013C000FF9EDB302F0022100013C000FF9EDC302F000EE048100013C000FF9EDD302F000E100013C000FF9EDE202F0014E088100013C000FF9EDF202F0014100013C000FF9EE0487800054878000B487900FF9ED64EB900FF8D8C508F588F600001387001C0AF00104A80671042A7487800BB4EBAFE04508F6000011E0CAF00FF7FFF0010630000B6202F0010D0AF00140C8000FFCDFF620000A442AF000A42AF001A6066222F001A24014C3C2C0051EB851FE8802401D482958220429088D08024007F99
[05:02:42:679]  RX: 6D F0 10 76 00 73
[05:02:42:699]  Found response, Success
[05:02:42:708]  Kernel upload 35% complete.
[05:02:42:722]  Sending block with offset 0x001000, start address 0xFF9000, length 0x0400.
[05:02:42:808]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:02:43:866]  RX: 6D F0 10 76 00 73
[05:02:43:890]  Found response, Success
[05:02:43:905]  Kernel upload 48% complete.
[05:02:43:917]  Sending block with offset 0x000C00, start address 0xFF8C00, length 0x0400.
[05:02:43:942]  Sending 'test device present' notification.
[05:02:43:952]  Setting timeout for Minimum, 0 ms.
[05:02:43:962]  TX: STPTO 0
[05:02:43:975]  OK
[05:02:43:988]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:44:024]  Empty response to STPX with data. OK.
[05:02:44:031]  Setting timeout for SendKernel, 50 ms.
[05:02:44:055]  TX: STPTO 50
[05:02:44:088]  OK
[05:02:44:156]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:02:45:226]  RX: 6D F0 10 76 00 73
[05:02:45:251]  Found response, Success
[05:02:45:283]  Kernel upload 61% complete.
[05:02:45:300]  Sending block with offset 0x000800, start address 0xFF8800, length 0x0400.
[05:02:45:384]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:02:46:459]  RX: 6D F0 10 76 00 73
[05:02:46:483]  Found response, Success
[05:02:46:492]  Kernel upload 74% complete.
[05:02:46:501]  Sending block with offset 0x000400, start address 0xFF8400, length 0x0400.
[05:02:46:512]  Sending 'test device present' notification.
[05:02:46:530]  Setting timeout for Minimum, 0 ms.
[05:02:46:555]  TX: STPTO 0
[05:02:46:569]  OK
[05:02:46:576]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:46:601]  Empty response to STPX with data. OK.
[05:02:46:608]  Setting timeout for SendKernel, 50 ms.
[05:02:46:623]  TX: STPTO 50
[05:02:46:649]  OK
[05:02:46:720]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:02:47:771]  RX: 6D F0 10 76 00 73
[05:02:47:798]  Found response, Success
[05:02:47:815]  Kernel upload 87% complete.
[05:02:47:840]  Sending block with offset 0x000000, start address 0xFF8000, length 0x0400.
[05:02:47:930]  TX: STPX H:6D10F0, R:1, L:1033
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
[05:02:49:021]  RX: 6D F0 10 76 00 73
[05:02:49:055]  Found response, Success
[05:02:49:070]  Kernel upload 100% complete.
[05:02:49:085]  TX: STPX H:6C10F0, R:1, D:3D00
[05:02:50:227]  Timeout during receive.
[05:02:50:367]  TX: STPX H:6C10F0, R:1, D:3D00
[05:02:50:430]  RX: 6C F0 10 7D 00 01 03 05 01
[05:02:50:454]  Kernel Version: 01030501
[05:02:50:476]  Kernel uploaded to PCM succesfully.
[05:02:50:493]  Sending 'test device present' notification.
[05:02:50:508]  Setting timeout for Minimum, 0 ms.
[05:02:50:516]  TX: STPTO 0
[05:02:50:538]  OK
[05:02:50:549]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:50:571]  Empty response to STPX with data. OK.
[05:02:50:581]  Setting timeout for SendKernel, 50 ms.
[05:02:50:600]  TX: STPTO 50
[05:02:50:635]  OK
[05:02:50:644]  Setting timeout for ReadProperty, 25 ms.
[05:02:50:666]  TX: STPTO 25
[05:02:50:699]  OK
[05:02:50:705]  TX: STPX H:6C10F0, R:1, D:3D03
[05:02:50:733]  RX: 6C F0 10 7D 03 00 13 6C AB
[05:02:50:739]  Trying P01 512Kb
[05:02:50:765]  PCM and image file are different operating systems.
[05:02:50:781]  But we'll ignore that because this is just a test write.
[05:02:50:796]  Sending 'test device present' notification.
[05:02:50:817]  Setting timeout for Minimum, 0 ms.
[05:02:50:837]  TX: STPTO 0
[05:02:50:859]  OK
[05:02:50:877]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:50:907]  Empty response to STPX with data. OK.
[05:02:50:912]  Setting timeout for ReadProperty, 25 ms.
[05:02:50:918]  TX: STPTO 25
[05:02:50:939]  OK
[05:02:50:952]  Sending 'test device present' notification.
[05:02:50:966]  Setting timeout for Minimum, 0 ms.
[05:02:50:979]  TX: STPTO 0
[05:02:51:003]  OK
[05:02:51:014]  TX: STPX H:8CFEF0, R:0, D:3F
[05:02:51:051]  Empty response to STPX with data. OK.
[05:02:51:062]  Setting timeout for ReadProperty, 25 ms.
[05:02:51:082]  TX: STPTO 25
[05:02:51:099]  OK
[05:02:51:105]  TX: STPX H:6C10F0, R:1, D:3D01
[05:02:51:134]  RX: 6C F0 10 7D 01 00 89 44 71
[05:02:51:146]  Flash chip: Intel 28F400B, 512kb
[05:02:51:163]  File size 524,288 does not match PCM size 0. This image is not compatible with this PCM.
[05:02:51:181]  Halting the kernel.
[05:02:51:201]  TX: STPX H:6C10F0, R:1, D:20
[05:02:51:261]  Clearing trouble codes.
[05:02:51:274]  Setting timeout for Minimum, 0 ms.
[05:02:51:291]  TX: STPTO 0
[05:02:51:307]  OK
[05:02:51:570]  TX: STPX H:686AF0, R:1, D:04
[05:02:51:648]  RX: 6C F0 10 60 CC 00 00 0A
[05:02:51:926]  TX: STPX H:686AF0, R:1, D:04
[05:02:52:967]  Empty response to STPX with data. That's not OK.
[05:02:53:246]  TX: STPX H:8CFEF0, R:1, D:14
[05:02:53:278]  Unexpected response to STPX with data: STOPPED
[05:02:53:559]  TX: STPX H:8CFEF0, R:1, D:14
[05:02:53:584]  Unexpected response to STPX with data: ?
[05:02:53:598]  Elapsed time 00:00:14.7330668
It's a previously tuned ECU as you can see by the HPTuners enhanced OSID, which was not locked. I apologise if this scenario has been answered previously, I had a bit of a look but wasn't able to find anything about it. Let me know if there's anything else I can try here, or provide that might give us some answers. Not exactly keen to desolder the 28F400B and take a read, hoping for a non-invasive solution as I literally have the car bolted to the dyno right now.
Attachments
Unable to read with hpt.png
Unable to read with hpt.png (21.83 KiB) Viewed 581 times
Top
User avatar
antus
Site Admin
Posts: 9007
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:
Contact antus

Re: Unable to read P01 PCM with PCMHammer or HPTuners

Post by antus »

osid starting with 127 is a HPT COS - one that pcmhammer doesnt have in its database. One day I'd like to add a function to read or write by type of pcm, not osid lookup. But that day isnt here yet. At the moment your only option is download pcmhammer source code, add the osid as a p01 type, compile it in visual c#, copy the kernels and use that. Dont know why hpt would say that. Maybe there is another problem too.. but it looks like pcmhammer has a chance of working if it could recognise it.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Top
Post Reply

Return to “GM LS1 512Kbyte and 1Mbyte and newer”