How to Adjust Shift Points for Smoother Shifting?

General Tuning Questions And Discussions
User avatar
iceburgslim
Posts: 5
Joined: Fri Oct 16, 2026 12:44 pm
cars: 1994 Mitsubishi Diamante
2000 Chevrolet Silverado 1500 5.3L V8

How to Adjust Shift Points for Smoother Shifting?

Post by iceburgslim »

I'm working on a stock-calibration 2000 Chevrolet Silverado 1500 with the 5.3L V8 and using Universal Patcher to view and edit the PCM calibration.

I'm looking for advice on adjusting the transmission calibration for smoother, more predictable shifts during light-to-moderate throttle driving.

What I'm experiencing:

The truck feels like it hesitates or bucks when I give it moderate throttle.
Power seems to come on suddenly around 45–50% throttle.
I'd like smoother, more consistent upshifts without making the transmission feel sluggish.
I want to retain normal daily-driver behavior and avoid unnecessary transmission wear.

Questions:

Which tables should I focus on first for shift scheduling: Normal Upshift, Performance Upshift, or both?
How should I adjust the 1–2, 2–3, and 3–4 shift points to make shifts smoother during light-to-moderate throttle?
Should I adjust the upshift start/end ratios, or are those tables related to something other than the actual shift schedule?
How do the Normal and Performance pressure tables affect shift feel, and should I leave them stock while adjusting shift scheduling?
Are there any other transmission calibration tables I should review before making changes?

I'm trying to understand the correct tuning process rather than randomly changing values. I can provide the PCM operating system ID and screenshots or exported values from Universal Patcher if needed.

I'd appreciate advice from anyone familiar with the early GM 5.3L PCM and transmission calibration.
You do not have the required permissions to view the files attached to this post.
ibs :driving:
User avatar
antus
Site Admin
Posts: 10111
Joined: Sat Feb 28, 2009 10:34 am
cars: TX Gemini 2L Twincam 8psi
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Subaru WRX 2007

Re: How to Adjust Shift Points for Smoother Shifting?

Post by antus »

First of all, what have you changed? If nothing, then it probably didn't shift like that from factory and there is probably a mechanical or electrical problem. Check your logs for sticky throttle sensor, check AFRs, check for DTCs. If you have changed something consider stumbles are often a result of poor tune. You may need to tune in your fuel better. If it's not that and you genuinely do need to change the trans I'll let someone else speak to transmission tuning as I do not have experience with that.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
User avatar
iceburgslim
Posts: 5
Joined: Fri Oct 16, 2026 12:44 pm
cars: 1994 Mitsubishi Diamante
2000 Chevrolet Silverado 1500 5.3L V8

Re: How to Adjust Shift Points for Smoother Shifting?

Post by iceburgslim »

Thanks for the reply. So far, the calibration changes I've made were disabling VATS and the B1S2/B2S2 rear oxygen sensor MILs and reporting. I haven't intentionally changed the transmission shift tables yet. Only codes i had was p0160 and p0140.
ibs :driving:
User avatar
antus
Site Admin
Posts: 10111
Joined: Sat Feb 28, 2009 10:34 am
cars: TX Gemini 2L Twincam 8psi
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Subaru WRX 2007

Re: How to Adjust Shift Points for Smoother Shifting?

Post by antus »

They are both o2 sensor failure codes so I would be suspicious if incorect AFR readings caused by fuel trims being out due to missing or incorrect readings from any other o2 sensors that may be about to fail. This could mess up your fueling which could cause your car to stumble. If you can, fixing o2 sensors and clearing dtcs and letting fuel trims pull the fuelling back in line would be more effective than trying to hack the trans to work around it.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
User avatar
iceburgslim
Posts: 5
Joined: Fri Oct 16, 2026 12:44 pm
cars: 1994 Mitsubishi Diamante
2000 Chevrolet Silverado 1500 5.3L V8

Re: How to Adjust Shift Points for Smoother Shifting?

Post by iceburgslim »

ok ty..... i just put a new fuel pump in it an then the codes started.
ibs :driving:
User avatar
pman92
Posts: 672
Joined: Thu May 03, 2012 12:50 pm
Location: Castlemaine, Vic

Re: How to Adjust Shift Points for Smoother Shifting?

Post by pman92 »

Agreed. If the vehicle was fine and then wasn’t, it has nothing to do with the calibration. If it all started when you did the fuel pump look there.
User avatar
iceburgslim
Posts: 5
Joined: Fri Oct 16, 2026 12:44 pm
cars: 1994 Mitsubishi Diamante
2000 Chevrolet Silverado 1500 5.3L V8

Re: How to Adjust Shift Points for Smoother Shifting?

Post by iceburgslim »

checked the fuel pump and pressure the ground, power, and signal are good... fuel pressure 60 truck on engine off.
ibs :driving: