Edit: Tried a second read and it went, but by 10% it was over 20 retries and was looking like it was going to take a half an hour and I didn't have that long to wait around. Can re-engage that tonight to see if I can get a successful read.
This blackbox has the same OS as in your original post, it is a 4 plug unit in a 99 Chevy K2500. Here's the properties.
[10:59:27:421] VIN: 1GCGK23J3XF025507
[10:59:27:468] OSID: 9365085
[10:59:27:484] Description: Vortec Black Box 98-02, 4 Plug, Service No 16263494
[10:59:27:516] Hardware ID: 872429914
[10:59:27:579] Broad Cast Code: CMUH
[10:59:27:623] MEC: 0
[10:59:27:673] Voltage: 11.4
Using that version I tried a read of the blackbox and got this:
[10:56:49:327] PCM Hammer (10/11/2024, 1:20 AM)
[10:56:49:329] Sunday, December 29 2024 @10:56:49:32
[10:56:49:331] ElmDevice initialization starting.
[10:56:50:462] TX:
[10:56:50:477] TX: AT Z
[10:56:51:347] ELM327 v1.4b
[10:56:51:347] TX: AT E0
[10:56:51:363] AT E0 OK
[10:56:51:368] TX: AT S0
[10:56:51:368] OK
[10:56:51:368] TX: AT RV
[10:56:51:378] Voltage: 11.7V
[10:56:51:378] TX: AT I
[10:56:51:399] Elm ID: ELM327 v1.4b
[10:56:51:399] Initializing PcmHacking.AllProDeviceImplementation
[10:56:51:399] TX: AT #1
[10:56:51:410] This is not an AllPro device.
[10:56:51:410] Determining whether PcmHacking.ScanToolDeviceImplementation is connected.
[10:56:51:410] TX: ST I
[10:56:51:431] ScanTool device ID: STN1155 v5.6.19
[10:56:51:431] TX: STPTO 3000
[10:56:51:459] OK
[10:56:51:459] TX: AT AL
[10:56:51:474] OK
[10:56:51:474] TX: AT SP2
[10:56:51:490] OK
[10:56:51:490] TX: AT DP
[10:56:51:532] SAE J1850 VPW
[10:56:51:532] TX: AT AR
[10:56:51:571] OK
[10:56:51:572] TX: AT AT0
[10:56:51:601] OK
[10:56:51:601] TX: AT SR F0
[10:56:51:617] OK
[10:56:51:617] TX: AT H1
[10:56:51:632] OK
[10:56:51:632] TX: AT ST 20
[10:56:51:648] OK
[10:57:13:371] Will save to C:\Users\d_moz\Documents\Tuning Stuff\PCM Hammer\PcmHammer021\BIN\Plow_Truck.bin
[10:57:16:241] Querying operating system of current PCM.
[10:57:16:256] Setting timeout for ReadProperty, 25 ms.
[10:57:16:256] TX: STPTO 25
[10:57:16:367] OK
[10:57:16:382] TX: STPX H:6C10F0, R:1, D:3C0A
[10:57:17:516] Timeout during receive.
[10:57:17:516] Sending 'test device present' notification.
[10:57:17:516] Setting timeout for Minimum, 0 ms.
[10:57:17:522] TX: STPTO 0
[10:57:17:548] OK
[10:57:17:548] TX: STPX H:8CFEF0, R:0, D:3F
[10:57:17:563] Empty response to STPX with data. OK.
[10:57:17:563] Setting timeout for ReadProperty, 25 ms.
[10:57:17:563] TX: STPTO 25
[10:57:17:580] OK
[10:57:18:618] Timeout during receive.
[10:57:18:618] Sending 'test device present' notification.
[10:57:18:620] Setting timeout for Minimum, 0 ms.
[10:57:18:620] TX: STPTO 0
[10:57:18:650] OK
[10:57:18:665] TX: STPX H:8CFEF0, R:0, D:3F
[10:57:18:681] Empty response to STPX with data. OK.
[10:57:18:683] Setting timeout for ReadProperty, 25 ms.
[10:57:18:683] TX: STPTO 25
[10:57:18:697] OK
[10:57:19:736] Timeout during receive.
[10:57:19:736] Sending 'test device present' notification.
[10:57:19:736] Setting timeout for Minimum, 0 ms.
[10:57:19:736] TX: STPTO 0
[10:57:19:767] OK
[10:57:19:767] TX: STPX H:8CFEF0, R:0, D:3F
[10:57:19:799] Empty response to STPX with data. OK.
[10:57:19:800] Setting timeout for ReadProperty, 25 ms.
[10:57:19:800] TX: STPTO 25
[10:57:19:802] OK
[10:57:20:840] Timeout during receive.
[10:57:20:840] Sending 'test device present' notification.
[10:57:20:840] Setting timeout for Minimum, 0 ms.
[10:57:20:840] TX: STPTO 0
[10:57:20:871] OK
[10:57:20:871] TX: STPX H:8CFEF0, R:0, D:3F
[10:57:20:899] Empty response to STPX with data. OK.
[10:57:20:899] Setting timeout for ReadProperty, 25 ms.
[10:57:20:899] TX: STPTO 25
[10:57:20:904] OK
[10:57:21:930] Timeout during receive.
[10:57:21:931] Receive timed out. Attempt #5, Timeout #5.
[10:57:21:931] TX: STPX H:6C10F0, R:1, D:3C0A
[10:57:22:009] RX: 6C F0 10 7C 0A 00 8E E6 5D
[10:57:22:009] Received: 6C F0 10 7C 0A 00 8E E6 5D
[10:57:22:009] OSID: 9365085
[10:57:22:027] Description: Vortec Black Box 98-02, 4 Plug, Service No 16263494
[10:57:22:027] Suppressing VPW chatter.
[10:57:22:027] TX: STPX H:6CFEF0, R:1, D:2800
[10:57:22:057] RX: 6C F0 C0 68 00
[10:57:22:057] Received: 6C F0 C0 68 00
[10:57:22:057] Sending 'test device present' notification.
[10:57:22:057] Setting timeout for Minimum, 0 ms.
[10:57:22:057] TX: STPTO 0
[10:57:22:057] OK
[10:57:22:057] TX: STPX H:8CFEF0, R:0, D:3F
[10:57:22:073] Empty response to STPX with data. OK.
[10:57:22:073] Setting timeout for ReadProperty, 25 ms.
[10:57:22:073] TX: STPTO 25
[10:57:22:088] OK
[10:57:22:088] Ignoring chatter: 6C F0 C0 68 00
[10:57:22:088] Sending seed request.
[10:57:22:088] TX: STPX H:6C10F0, R:1, D:2701
[10:57:23:178] Timeout during receive.
[10:57:23:178] No response to seed request.
[10:57:23:178] Unlock was not successful.
PCM Hammer 98/99 Black Box Support
-
- Posts: 2
- Joined: Sat Dec 28, 2024 12:50 am
- antus
- Site Admin
- Posts: 8688
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: PCM Hammer 98/99 Black Box Support
Yeah the scantool devices are pretty rubbish. They are a very slow protocol and also don't support 4x speed. I would like to drop support for them, but I guess slow is better than not at all and it should keep working if we just leave the code in there.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
- antus
- Site Admin
- Posts: 8688
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: PCM Hammer 98/99 Black Box Support
The test version is on the last page of the thread if you want to try the 99 on the bench and let us know.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: PCM Hammer 98/99 Black Box Support
It reads but crc check procedure not started
ObdLink SX latest firmware
PCM were tuned by HP tuners before (not locked) by me
ObdLink SX latest firmware
PCM were tuned by HP tuners before (not locked) by me
- Attachments
-
- PcmHammer_debugLog_20250112@111616.txt
- (3.34 MiB) Downloaded 34 times
-
- Posts: 89
- Joined: Sat Jun 25, 2022 1:35 am
- cars: 1982 Chevy Chevette 3400 LA1 swapped
1986 Chevy Chevette
1998 Chevy s10
Re: PCM Hammer 98/99 Black Box Support
I've been occasionally getting that same Object reference error during crc checks, restarting my laptop usually solves it for a while so I can get a few reads/writes before it starts throwing the error again.
Re: PCM Hammer 98/99 Black Box Support
What adapter do u use ? Maybe its because energy savings features cuz laptops has a lot of by default ?
I use PC and power supply to PCM from MOLEX 12V -works excellent with P01-P59