Muncies vy Turbo v6
-
Muncie
- Posts: 231
- Joined: Wed Dec 02, 2020 6:15 am
- cars: Vy commodore, Turbo Ecotec v6
- Location: New Zealand Waikato
Re: Muncies vy Turbo v6
@Rhysk94 l36 $06a enhanced v0.9 i think back then.
-
Rhysk94
- Posts: 235
- Joined: Sun Mar 15, 2020 9:25 am
- cars: VE SS-V
VY V6 Turbo “Ecojet”
FG XR6 Turbo
VY V6 Stocker Farm Hack
VY V6 Turbo Competition Drift Car
VY V6 L67 Seat Time Drift Car
N80 Toyota Hilux
VZ SS - Location: Perth
Re: Muncies vy Turbo v6
Ooof, spiceeeee
-
Muncie
- Posts: 231
- Joined: Wed Dec 02, 2020 6:15 am
- cars: Vy commodore, Turbo Ecotec v6
- Location: New Zealand Waikato
Re: Muncies vy Turbo v6
Yeah, it went well for 12 months and blew up....... learned some things.
-
Rhysk94
- Posts: 235
- Joined: Sun Mar 15, 2020 9:25 am
- cars: VE SS-V
VY V6 Turbo “Ecojet”
FG XR6 Turbo
VY V6 Stocker Farm Hack
VY V6 Turbo Competition Drift Car
VY V6 L67 Seat Time Drift Car
N80 Toyota Hilux
VZ SS - Location: Perth
Re: Muncies vy Turbo v6
Surprised it lasted that long with that much timing up its ass 
Just fyi, thats more than you run on forged setups..
Just fyi, thats more than you run on forged setups..
-
Muncie
- Posts: 231
- Joined: Wed Dec 02, 2020 6:15 am
- cars: Vy commodore, Turbo Ecotec v6
- Location: New Zealand Waikato
Re: Muncies vy Turbo v6
I did pull timing out of it under boost but nowhere near enough most likely. Got a far better grasp on that side of it now. It broke because I gave it 2 clicks on boost controller when I should of left it alone.
Ive done the HP academy courses now and will run through them again before I bolt turbo back on even then I'll take my time with it and get it on a dyno.
Ive done the HP academy courses now and will run through them again before I bolt turbo back on even then I'll take my time with it and get it on a dyno.
-
Rhysk94
- Posts: 235
- Joined: Sun Mar 15, 2020 9:25 am
- cars: VE SS-V
VY V6 Turbo “Ecojet”
FG XR6 Turbo
VY V6 Stocker Farm Hack
VY V6 Turbo Competition Drift Car
VY V6 L67 Seat Time Drift Car
N80 Toyota Hilux
VZ SS - Location: Perth
Re: Muncies vy Turbo v6
Problem with the hp courses is that they have nothing to do with these motors. The timing they like is completely different.
Flick me a message and I'll let you know. Not going to publically post it as all thw tiktok tuners will start advertising they can tune boost



Flick me a message and I'll let you know. Not going to publically post it as all thw tiktok tuners will start advertising they can tune boost
-
Muncie
- Posts: 231
- Joined: Wed Dec 02, 2020 6:15 am
- cars: Vy commodore, Turbo Ecotec v6
- Location: New Zealand Waikato
Re: Muncies vy Turbo v6
Thanks for the Advice Rhys, Got everything in its now commanding timing in a safe range and showing Zero! knock events Which is awesome, Fueling is close its a bit rich trims are pulling about 5% in parts but thats better than lean early on.
Just on 6psi its Pretty lively i forgot i didnt have catch can fitted yet on test drive so couldnt stay in it for long but got a short Log.
My Wideband is off at idle showing 10.0 afr but comes back online in the right range once up on boost, think its a ground problem as the Trims arent out the park on Tunerpro Dash, I'll check my Earth for it and chuck a new sensor in. I'm just glad its not dead on Lawn anymore and i can hop in get the milk and bread in it.
Just on 6psi its Pretty lively i forgot i didnt have catch can fitted yet on test drive so couldnt stay in it for long but got a short Log.
My Wideband is off at idle showing 10.0 afr but comes back online in the right range once up on boost, think its a ground problem as the Trims arent out the park on Tunerpro Dash, I'll check my Earth for it and chuck a new sensor in. I'm just glad its not dead on Lawn anymore and i can hop in get the milk and bread in it.
-
Muncie
- Posts: 231
- Joined: Wed Dec 02, 2020 6:15 am
- cars: Vy commodore, Turbo Ecotec v6
- Location: New Zealand Waikato
Re: Muncies vy Turbo v6
All the gear back in engine bay now its a busy place.
Gave it beans today pulls well went to 5500rpm still early days has heaps of oil pressure after rebuild 90psi above idle and 40psi at idle cant complain there.
Gave it beans today pulls well went to 5500rpm still early days has heaps of oil pressure after rebuild 90psi above idle and 40psi at idle cant complain there.
You do not have the required permissions to view the files attached to this post.
-
immortality
- Posts: 3820
- Joined: Thu Apr 09, 2009 2:31 am
- cars: VS,VT,VX,VE
Re: Muncies vy Turbo v6
I have a spare flash PCM here that is no use to me, not 100% sure what it's from but you are welcome to it.
-
Muncie
- Posts: 231
- Joined: Wed Dec 02, 2020 6:15 am
- cars: Vy commodore, Turbo Ecotec v6
- Location: New Zealand Waikato
Re: Muncies vy Turbo v6
Will never say no to another for the shelf.immortality wrote: Fri Feb 06, 2026 8:13 am I have a spare flash PCM here that is no use to me, not 100% sure what it's from but you are welcome to it.