DELCOS NEW RIDE

[delcowizzid]

vb power figure is in over 280kw/380hp at the wheels @ 5800 or some shit on 14psi printer was out of ink awaiting printouts via email and 600+nm of torque at 4800

[The1]

nice , is there any engine work?

[delcowizzid]

a custom kelford cam and 1.6 YT rockers in a 340000+km engine LOL
and a chinese t70 LOL

[The1]

doing alright then, seen a few pass's now.

[Specops]

have a look at my 808 $123p ecotec tune, its probably going to be a pretty close starting point for timing and ve for the VR PCM!

I know this is probably a dumb question but could i put a 808 memcal in my vs ecotec with this $123p ecotec tune?

[Holden202T]

not in a VS computer, you would need to run a vn/vp or vr manual comptuer to use $12 ecotec tune.

[sprattzvx]

man these buicks must be pretty hardy thats good power. damien(boost obsession)is fabbing me up a set of manifolds to suit l67 into vn on a borg warner s366 , cant wait to get in on this rediculous turbo powa

[delcowizzid]

update time and its pretty big and full of awesome win

so the starlet goes to get its cage this week so we had to get it ready 1 night and 2 guys with a 1mm cutoff wheel later and its ready for its cage and 4 link rearend to be fitted

i didnt get the before shots but here it is on our first workbench after picking it up and cutting out the rear while we could get under it

IMGP5883.jpg (65.27 KiB) Viewed 3093 times

IMGP5885.jpg (98.59 KiB) Viewed 3093 times

IMGP5887.jpg (149.81 KiB) Viewed 3093 times

now offloaded onto the shed floor with shortened BW diff in place.some new 10" wheels and used ET STREETS that ive borrowed for mock up on also more inner gaurds removed

IMGP5889.jpg (129.22 KiB) Viewed 3093 times

IMGP5899.jpg (52.45 KiB) Viewed 3093 times

IMGP5900.jpg (122.8 KiB) Viewed 3093 times

rims and tyres for level blocks LOL

IMGP5891.jpg (112.2 KiB) Viewed 3093 times

front on the ground body leveled engine and trans is in allready

IMGP5892.jpg (98.76 KiB) Viewed 3093 times

IMGP5894.jpg (113.41 KiB) Viewed 3093 times

IMGP5895.jpg (106.78 KiB) Viewed 3093 times

28" needed some more space out with the trusty 1 mill again

IMGP5896.jpg (98.54 KiB) Viewed 3093 times

IMGP5901.jpg (102.63 KiB) Viewed 3093 times

IMGP5903.jpg (111.64 KiB) Viewed 3093 times

my mate whos shed its in is a chev nutter and had to mock up the 8 trumpet meth setup just so we could see what it would look like with a chev in it

IMGP5905.jpg (109.79 KiB) Viewed 3093 times

IMGP5904.jpg (103.3 KiB) Viewed 3093 times

IMGP5906.jpg (86.71 KiB) Viewed 3093 times

all in all a good couple of days work

[Holden202T]

this thing looks cool, and looks very tough with the big fatties!
cut to trumpts of that manifold and use it on the v6

[delcowizzid]

cant wait to get the twin turbo v6 connected to them big fatties and do some skids