dtc 43

[boosted falcon]

im really not sure it was purchesed off ebay , when hooked up to tunerpro under flags it says its a manuel v8, as it a auto v6 and its only showing codes 15, 59 and the paperclip shows diffrent codes somthing must be wrong it should trow the same codes as the clip yeah ? the fella i got it off is looking into y the codes are only from 15-59 and checking the adx file , waiting to here back. the vt ecu has a stock memcal is there any point putting that in and trying the vt adx. ?

[VL400]

Try the ADX from here .. https://pcmhacking.net/forums/view ... ?f=10&t=29

The one you have is all wrong.

[boosted falcon]

just tried new adx file there is alot more info there now under engine sensor data the wideband o2 is 36.26 and in red

the iat valtage is 3.14 and also red, under flags the est mode has bypass next to it( both in

green) and the malf present is set in red . under dtc codes 59, 67, 82 are set the only codes missing now that i can see are 12 ,47, 49. and 73 and in dash it says bcm disabled and o2 sensors not ready and tcc off??

do i need the xdf. and bin. selected?

[charlay86]

you don't need a bin or xdf. The bin is what is on the memcal, you would need to read it first. the xdf defines what the raw data in the memcal actually represents.

Ignore wideband O2 if you don't have one connected.
if the engine isn't running the 02 sensors won't be ready, and the tcc will be off unless the car is cruising at a decent speed.
dtc 12 means the engine is not running.

[boosted falcon]

im getting a read out of 447 on the left 02 sensor and 451 on the right still says 02 status not ready, whats the go with the bcm being disabled , malf present and the est mode bypass? for some reason the car idels now very poorly but idels and it smells rich as?

[Holden202T]

can you record a log and post it up along with the adx your using ?

[boosted falcon]

$51 VS V6 Engine and Trans v1.10 WB 14.7kit.adx

(145.15 KiB) Downloaded 274 times

vs data log rec.xdl

(25.77 KiB) Downloaded 262 times

this is the data log and adx preety sure i did it right . cheers fellas

[VL400]

BLM disabled = read the FAQ (linked to you the other day) for what it means https://pcmhacking.net/forums/view ... f=7&t=1396
O2 sensor at ~450mV = engine cold, see what they do when the engine warms up
EST Bypass = To do with ignition. Bypass mode normally during crank or fault and EST when the ECU is in control of spark advance

Need to sort out your trans temp, its open circuit, plus some other trans faults.

But yes, idle is surging and looks to be running pretty poor - might be time to speak to the tuner now you can log it. Or, use the flashtool (https://pcmhacking.net/forums/viewtopic.php?f=3&t=82) and extract the bin and post it up. To use it, open the program under Options and preferences select the com port and the vehicle type "VS Ecotec or S/C PCM in Vehicle", click ok and connect. After it identifies the PCM click get bin.

[boosted falcon]

vs bin..bin

(128 KiB) Downloaded 374 times

heres the bin,


and im guessing the auto error codes are becuse of the vt auto in the vs can the ecu be re programed to reconise the vt auto or is it easyier to just fit a vs auto ?

[vs ss]

The auto box will work fine as the electrics inside the two are the same and the series 3 vs used the vt box.
I often change the cooler lines and put vt vx vy v6 transmissions into vs commys with no probs.
But if you want you could use a late fullcircle trans tune from a vs series 3 ute.
Is the big plug on top of the trans plugged on propely?