Vlad's rides thread
-
vlad01
- Posts: 8124
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Vlad's VP executive (Now VR)
lol thats weird? I had the opposite experience. I was spewing actually. I have an unused roof lining I can't use as its got holes for the mirror but I want to stick to the glass mount in the VR.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
vs ss
- Posts: 590
- Joined: Thu Nov 03, 2011 7:57 pm
- cars: hsv enhanced vs ss
vt xu6
fb holden
toyota landcruiser
vt ss s1 - Location: perth wa
Re: Vlad's VP executive (Now VR)
LOL I done the same on a vs,i had a mint vr hoodlining with the hole so I had to use the vr mirror.
Cause if I had to buy the correct hoodlining I would of doubled the value of the car
Nice job on the vr so far.
Cause if I had to buy the correct hoodlining I would of doubled the value of the car
Nice job on the vr so far.
-
vlad01
- Posts: 8124
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Vlad's VP executive (Now VR)
cheers!
yeah my roof lining is one I re-upholstered my self, but it is the wrong colour for VP as the charcoal lining material wasn't available at the time, then I did get some of the right colour. but this one is the right colour more or less for the VR and I can't use it.
I can't even sell it. damn cheap ass "other" commodore owners lol
yeah my roof lining is one I re-upholstered my self, but it is the wrong colour for VP as the charcoal lining material wasn't available at the time, then I did get some of the right colour. but this one is the right colour more or less for the VR and I can't use it.
I can't even sell it. damn cheap ass "other" commodore owners lol
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
vlad01
- Posts: 8124
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Vlad's VP executive (Now VR)
- IMG_1159_zps01ef7c29.jpg (102.95 KiB) Viewed 3772 times
- IMG_1160_zpsab6600a0.jpg (77.26 KiB) Viewed 3772 times
- IMG_1161_zpsfd3581fb.jpg (95.15 KiB) Viewed 3772 times
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
monaro308
- Posts: 343
- Joined: Sat Mar 21, 2009 2:02 pm
- cars: VT S1 LS1 C/dore track car
HJ GTS Monaro Coupe
CV8 V2 S3
VE SSV
Re: Vlad's VP executive (Now VR)
Coming up a treat
-
vlad01
- Posts: 8124
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Vlad's VP executive (Now VR)
it is!
so the list is reduced to this.
cruise control safety for the clutch, PCBs are being made this week, just getting on to a laser cutter for the sensor mounts now.
refit steering column.
gear box to be have basic overhaul and fitted, new VSS to be fitted too.
fit tailshaft
refit injectors
fit modded 808 and then we can have a test run!
Then after that:
windscreen replacement
roof lining
get the rest of the exhaust
fit bonnet and new insulation mat
decent tyres and front end alignment
sort out some new front guard badges (black paint peeling off)
roady and rego
tuning time! and fun!
When the good warm weather comes again, new front bar to really make it look new.
so the list is reduced to this.
cruise control safety for the clutch, PCBs are being made this week, just getting on to a laser cutter for the sensor mounts now.
refit steering column.
gear box to be have basic overhaul and fitted, new VSS to be fitted too.
fit tailshaft
refit injectors
fit modded 808 and then we can have a test run!
Then after that:
windscreen replacement
roof lining
get the rest of the exhaust
fit bonnet and new insulation mat
decent tyres and front end alignment
sort out some new front guard badges (black paint peeling off)
roady and rego
tuning time! and fun!
When the good warm weather comes again, new front bar to really make it look new.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Vlad's VP executive (Now VR)
Are you getting a full exhaust? Tein hi flow cats 2.5" system etc
-
vlad01
- Posts: 8124
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Vlad's VP executive (Now VR)
yep, mandrel bend 2.5" and higher flow cat, legal one, 200cpi or more.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
vlad01
- Posts: 8124
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Vlad's VP executive (Now VR)
Finally some sunny days as of recently.
Enough to get a good look of the progress, engine looks a million bucks
yesterday I did the best hand wheel alignment job I could and lock in the tie rods at that. Slight toe in (measured about 3-4mm) , and roughly centralized steering.
PS rack all sorted, hoses done and DXIII filled. Coolant done about a week ago, no leaks, shouldn't be any as I had it all running when I did the major gaskets. Only thing different this time is the timing cover and water pump but I sealed those to the best of my previously experiences and little tricks I learned in the past. Also sorted out my WB wiring. I made it plug and play but using a faulty O2 sensor's socket, removed the wires and soldered in the WB, extra green wire with single way plug goes to the cabin where it plugs into the harness near the ECU. I just hang the wire though the door and close it in there. Works just fine
Enough to get a good look of the progress, engine looks a million bucks
yesterday I did the best hand wheel alignment job I could and lock in the tie rods at that. Slight toe in (measured about 3-4mm) , and roughly centralized steering.
PS rack all sorted, hoses done and DXIII filled. Coolant done about a week ago, no leaks, shouldn't be any as I had it all running when I did the major gaskets. Only thing different this time is the timing cover and water pump but I sealed those to the best of my previously experiences and little tricks I learned in the past. Also sorted out my WB wiring. I made it plug and play but using a faulty O2 sensor's socket, removed the wires and soldered in the WB, extra green wire with single way plug goes to the cabin where it plugs into the harness near the ECU. I just hang the wire though the door and close it in there. Works just fine
- IMG_1166_zps7b61b4ea.jpg (118.32 KiB) Viewed 3772 times
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Vlad's VP executive (Now VR)
Should be good, do the V6's like twin cat set up's? I've always ran them on V8'svlad01 wrote:yep, mandrel bend 2.5" and higher flow cat, legal one, 200cpi or more.