Tuning training required in victoria
Re: Tuning training required in victoria
Thought it was just my end. I could hear hardly any voices.
I've never used skype but i could see names scrolling in the top right but no voices.
I've never used skype but i could see names scrolling in the top right but no voices.
-
- Posts: 149
- Joined: Wed Oct 31, 2012 6:59 pm
- cars: VY commodore supercharged V6
- Location: Sydney
Re: Tuning training required in victoria
Holden202T wrote:so if your recording has The1's voice ? are you willing to upload ?0081(2) wrote:I got a recording and watched it later. Gave me a bit to think about and loom forward to another one, if it happens
I too couldn't make it but would be keen to watch it
Yep it does have The1's voice but it also has a bit of background noise, i left the laptop recording in another room and it didn't dawn on my it would pickup any voices while it was recording.
The worst part is at the start but even then its not that bad also one part at the end when i pick the laptop and i was talking to the other half.
When i played it back and could hear all the background noise i though crap i hope you all didn't have to listen to that, then remembered that i did mute the Skype mic. Sorry if i did stuff it and you could hear the kids crying in the background at the start
I also left the camtasia window open in the bottom right corner which slightly blocked some on the page not really a issue it only really affects it when The1 was going through the enhanced PDF. and skype blocked some in the middle of the bottom.
I only downloaded camtasia as it started and was in a bit of a rush to get it setup. I don't know if its worth while posting it but if someone wants to try and strip the audio out try and sync it to The1's recording i can pass it on.
Re: Tuning training required in victoria
PM sent.The1 wrote:im in QLD so +10
i got camtasia on, installed an older version and got another 30days and it's working so should be good.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726

Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726

Re: Tuning training required in victoria
If you can get it up somewhere i still have my camtasia files so can sync up the audio stream.0081(2) wrote:Holden202T wrote:so if your recording has The1's voice ? are you willing to upload ?0081(2) wrote:I got a recording and watched it later. Gave me a bit to think about and loom forward to another one, if it happens
I too couldn't make it but would be keen to watch it
Yep it does have The1's voice but it also has a bit of background noise, i left the laptop recording in another room and it didn't dawn on my it would pickup any voices while it was recording.
The worst part is at the start but even then its not that bad also one part at the end when i pick the laptop and i was talking to the other half.
When i played it back and could hear all the background noise i though crap i hope you all didn't have to listen to that, then remembered that i did mute the Skype mic. Sorry if i did stuff it and you could hear the kids crying in the background at the start
I also left the camtasia window open in the bottom right corner which slightly blocked some on the page not really a issue it only really affects it when The1 was going through the enhanced PDF. and skype blocked some in the middle of the bottom.
I only downloaded camtasia as it started and was in a bit of a rush to get it setup. I don't know if its worth while posting it but if someone wants to try and strip the audio out try and sync it to The1's recording i can pass it on.
- Holden202T
- Posts: 10394
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Tuning training required in victoria
how bigs the file ? I have an FTP site you guys can use ?
No matter what the question is, the answer is always more horsepower! 
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread

Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
-
- Posts: 149
- Joined: Wed Oct 31, 2012 6:59 pm
- cars: VY commodore supercharged V6
- Location: Sydney
Re: Tuning training required in victoria
Its 1.35g
Re: Tuning training required in victoria
Might go better putting that onto a dropbox account. Then one of the guys can download it and try syncing up the audio.0081(2) wrote:Its 1.35g
Pretty sure you can strip the 'mic' noise completely and keep the 'system' noise which should The1 and everyone talking. Ill have to double check that camtasia has that ability!
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726

Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726

-
- Posts: 149
- Joined: Wed Oct 31, 2012 6:59 pm
- cars: VY commodore supercharged V6
- Location: Sydney
Re: Tuning training required in victoria
Ill up load it to my drop box account then.
The1 if you want to pm me your email ill send you the link.
The1 if you want to pm me your email ill send you the link.
-
- Posts: 445
- Joined: Sun Mar 22, 2009 11:52 am
- cars: VT V6 supercharged in a corolla
- Location: Sydney
- Contact:
Re: Tuning training required in victoria
kojab wrote:I am looking forward to the conference on Saturday as is would be an ideal time for me to introduce my 30 Hz VX/VY TP logger which will compliment Nigel’s enhanced bins.
The1 wrote:would be good to see.
I have put a 30Hz bin and adx in the “Custom Code” section of this forum for you to look at. New topic name is 30HZ logging for VX/VY flash PCMs
Let me know your thoughts
Cheers
Dick
Re: Tuning training required in victoria
I think TMPGEnc and VLC can allow you to split the video and audio, so the audio could be significantly smaller.0081(2) wrote:Its 1.35g
Joe.