Vlad's rides thread

[delcowizzid]

is it VR have a good look at the cam bearings lost count of how many vr models have had them spinning or falling out normally takes out the rest of the bearings after and causes the old piggybacked bigend bearings causing engine lockup.this is series 1 bearings after high km and lots of boost and limiter and thin as hot oil LOL dont mind the flat one it was used to roll new top shells in while engine was together LOL

IMGP4421.jpg (191.49 KiB) Viewed 3765 times

IMGP4424.jpg (170.08 KiB) Viewed 3765 times

bigends

IMGP4422.jpg (160.02 KiB) Viewed 3765 times

[vlad01]

its a VP engine, cam bearings are fine.

So VN ones only have 1 hole per shell? and dont seem to have the oil groove extend into the bottom shells like mine do.


I have noticed that on my big ends the shells have been fretting in the bores, they can be closed up fully by hand without bolting them, so there is almost no crush. I think that may contribute to spinning them in many engines with good oil pressure. They seem to be too loose lol. Im getting them resized with ARP bolts so that will make them bullet proof.


I heard many gluing the cam bearings in with epoxy.

[Holden202T]

you could use them again

[vlad01]

So I picked up my heads.

IMG_2271_zps2xgbvjvf.jpg (221.7 KiB) Viewed 3764 times

IMG_2273_zpssrfi7wt5.jpg (224.78 KiB) Viewed 3764 times

IMG_2272_zpsm9iyqxgd.jpg (208.02 KiB) Viewed 3764 times

unshrouded valves a bit.

IMG_2275_zpslyo8spum.jpg (185.94 KiB) Viewed 3764 times

nice port work.

IMG_2276_zps6o2mxoss.jpg (201.91 KiB) Viewed 3764 times

but there was a minor stuff up, the bosses on one head was missed, while the other head was done.

IMG_2277_zpsgi7kdj40.jpg (213.99 KiB) Viewed 3764 times

Will let them know this tomorrow or Monday. Otherwise its a damn awesome job. The finish on the faces is awesome, so smooth its more than good enough for MLS even.
0.010" was removed and they cleaned up awesome as. Best surfacing I have ever seen to be honest.

its got new exhaust seats. Crow cam springs performance springs for 308 V8 as the V6 springs they said were too weak and the next ones up were way too much for my cam.
So the specs are 110lb at seat and 265lb at max lift?

multi angle valve job with back cut, radiused seats and blended. They said the ports are not the best as there is material missing from some key areas that would make them better. They can't add cast iron only take it away

[VL400]

No messing about, didnt take long for them to come back!

[vlad01]

except one will have to go back lol. Have no idea how they missed that.

[vlad01]

also holden do happen to have a few pairs of lifter guides lets, about 5 pairs nation wide. so I have ordered 2 pairs at 66 a pair (discounted price ) , not cheap considering about 12 bucks from the USA when they were available. They also happen to have exactly 2 sets of VR bearing type rocker pedestals left, 24 in total in the country lol.

21 each normal price so its not too bad, cheaper than from the USA which are NLA too. Might order those next time once I confirm they are a direct fit for VP as well.

[Gareth]

They can't add cast iron only take it away

Ever heard of devcon?, i have used it extensively on 202 heads with never a problem.

[vlad01]

not keen on using epoxy for daily driver I expect to drive to 300k+

[vlad01]

got the other side of the tank finished today.

before

IMG_2279_zpsilo3k4sv.jpg (241.8 KiB) Viewed 3764 times

after

IMG_2280_zps0ynfualn.jpg (159.29 KiB) Viewed 3764 times

will be nice and rust proof now! and clean up a lot easier when I wash the car.